Info

Miscellaneous

# How many pieces of cloth can be cut from a 5 Metre length of cloth if each piece is 50 cm long?

## How many pieces of cloth can be cut from a 5 Metre length of cloth if each piece is 50 cm long?

5metre piece Thus 50 centimetres means 50/100 metres which equals 0.5 metres. Using elementary maths it follows that yo can cut 10 pieces of cloth, each of 50 cm (or 0.5 metres) from a 5 metre piece.

## How many pieces of 1.25 m each can be cut from a wire 40 m long?

=40. =40. So 4040 pieces of 1.25 m1.

## How many pieces of ribbon can cut from 10 meters if each piece is 4 cm long?

250 pieces of ribbons can be cut from it.

## How long is a piece of cloth?

The length is usually either 40 or 100 yards (37 or 91 m), but varies depending on the fabric being referred to; for example, a bolt of canvas is traditionally 39 yards (36 m).

## How many pieces of 50 cm can you get from a cloth that measure 2.5 Metres?

Since 2.5m=250cm, Therefore 250/50=5. 5 pieces is the answer to the question.

## How do you cut the perfect wood?

To make this cut, use a miter saw or a table saw for best results. A table saw will let you cut wider pieces of wood. Avoid using a band saw, as crosscutting wood is more strenuous on a blade and a band saw is more likely to burn the edges of the wood or result in rough cuts.

## Can you cut 2×4 with miter box?

When it comes to talking about the cutting capacity of the 10-inch miter saw, it will cut the 4×4 wood. But to do so it will pass some hard time. By using the stationary miter saw with 10-inch blade, you won’t be able to cut a 4×4 in one swing.

## How much is in a roll of fabric?

Rolls typically start at 50 yards; however, it depends on the product. Please see the individual product pages for roll sizes or contact us.

## What do you call a large piece of fabric?

sail, canvass, canvas, sheet – a large piece of fabric (usually canvas fabric) by means of which wind is used to propel a sailing vessel.

## What is the best tool to cut wood straight?

You can use both a jigsaw or a circular saw to cut wood in straight lines, but you will get the most accurate cuts, by using the circular saw. Nevertheless, the jigsaw is very versatile if you use the right cutting techniques.

## How much wood do you lose when you cut it?

Cutting something into 18 pieces means 17 kerfs: 17 times 0.125 inches equals 2.125 inches of wood that will be wasted in saw kerfs.

## How big of a log do you need to cut a log?

Measure the length of the log and round it down to the nearest even foot. For example, if you have a 15’3″ log, use the 14′ long length in the log rule table. Most loggers will cut logs into lengths only an inch or two greater than the nearest even foot.

## How to calculate the length of a piece of wood?

Let’s assume it’s five wooden boards. Choose the dimensions of the boards. For example, a piece of hardwood can be 8 feet long, 10 inches wide, and 1.25 inches thick. Substitute these numbers into the board foot formula to find the board footage per piece: board feet = length(ft) * width(in) * thickness(in) / 12 board feet = 8 * 10 * 1.25 / 12

## How to cut a 2 / 3 meter long string?

unfold the string, lay one end of it on one mark, and fold it up to so the other end is on the other mark. The new fold is at half a metre. Regard the 2/3 meter string as a 4/6 meter string. Fold the string in half. Then, without cutting, fold, one of the halves (i.e. 2/6 segment) back on itself. That last folded part is 1/6th of a meter.

## How big is a standard piece of timber?

The Timber Merchant, in general won’t stock the smaller sizes and will prefer to sell the longer lengths. The lengths are an approximation of the old Imperial sizes in feet, hence the 300mm increments. The timber sizes detailed here are UK standard sizes. I believe U.S. sizes are similar but in old fashioned inches. Timber Grades, Unsorted ?

## How much wood can you cut with a sliding miter saw?

With the same 10 inch blade, you can cut into wood or plywood up to 2 inches, as opposed to just 1.25 inches with a non-sliding miter saw. While a non-sliding miter saw may only let you crosscut a board 6 inches with a 10 inch blade, a sliding miter saw will let you cut almost twice as much.

## How big of a blade do you need to cut wood?

You can use a 10 inch blade to make right angle cuts on a 5.5 inch wide board. This means that you’ll have no problem working with 2×6 pieces of lumber. However, the thickness of the wood is not the only factor here.

## How big is a 16 foot lumber tree?

Determining Tree Volume Diameter 4 ½ feet above ground (inches) Number of 16-foot logs Number of 16-foot logs Number of 16-foot logs Number of 16-foot logs Diameter 4 ½ feet above ground (inches) 1 2 3 4 10 35 60 11 45 75

## How big of a chainsaw do I need for cutting trees?

I know from personal experience working in the forestry industry for years. A gas-powered chainsaw with a bar length of 20 inches or more is most effective for felling large hardwood trees such as oak, spruce, birch, beech and hemlock, many of which can be 30 – 36 inches in diameter.