Info

The hedgehog was engaged in a fight with

Read More
Guidelines

How long do Namco Pools last?

How long do Namco Pools last? 3-5 years Generally 3-5 years. Is Namco Pools still in business? Yes, We're Still Open! We're Still Open! Where are Namco Pools manufactured? Japan Designed in North America and produced in Japan using the Toyota Production System (TPS), Proline pools are of the highest quality, but at a fraction of the cost. Does Namco test pool water? Before the kids jump in the pool, then it is important to test and balance the pool water. NAMCO finds the following water levels work well for general pool conditions....Regular Store Hours.Monday - Saturday9am – 7pmSunday10am –...
Miscellaneous

Why are the Jets on my Pool not working?

Why are the Jets on my Pool not working? Jets are not working either. I have tried back flushing, but it does not seem to help. The pressure gauge works as when back flushing it changes but once I close the system it goes back to 0. I was told it should be between 20 - 25 for the jets to work properly. Of course pool is cloudy and looking dirty due to filter not working correctly. What to do if you suspect a leak in your pool? If you suspect a leak in your pool’s plumbing, contact Leak Science...
Trending

What to do if free chlorine is lower than total chlorine?

What to do if free chlorine is lower than total chlorine? If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small. Is total chlorine or free chlorine more important? In clean water, the amount of total chlorine can be used to determine the amount of free chlorine in the...
Lifehacks

Why is my Jandy PDA stuck on waiting?

Why is my Jandy PDA stuck on waiting? Cycle the computer My Jandy PDA is also stuck on waiting. Cycle the computer power breaker and it connects as usual. Power PDA off and on again, stuck in waiting. … read more What to do if you're not into PDA? In this situation, Mitchell says you should honor your feelings and take things as slowly as you'd like. Whatever your reason for being PDA-averse, it's best not to make a bigger deal out of it than it is. According to Mitchell, "The more important factor is the intention behind or need...
Trending

What is the meaning of stand pipe?

What is the meaning of stand pipe? : a high vertical pipe or reservoir that is used to secure a uniform pressure in a water-supply system. What is a standpipe UK? A standpipe is a free standing pipe which is fitted with a tap. You can easily attach this to a hydrant to get a water supply where there is no running water supply. A standpipe is a means of connecting to our water distribution network for a temporary water supply. What is a plumbing standpipe? A standpipe is an open-ended, metal pipe that can be screwed into a basement...
Trending

How do you treat smelly pipes?

How do you treat smelly pipes? Bring a pot of water or white vinegar almost to a boil and pour half of it slowly down the drain. Wait for a few minutes, rinse the pipe with cold water to solidify any lingering gunk, and pour the rest of the hot water or vinegar down the drain to wash it away. How to get rid of a stinky drain? 4 Home Remedies for Stinky Drains 1 The first thing you can do, and the most simple, is to remove any type of stopper from your sink... 2 The second thing that...
Q&A

What tools do you need to replace a faucet?

What tools do you need to replace a faucet? Removing a kitchen faucet requires two must-have tools: a basin wrench and an adjustable wrench. Use the adjustable wrench to give you the leverage you need. Unscrew the nuts and disconnect the water supply lines. The basin wrench is designed to work in tight spaces. What tools do I need to install a kitchen faucet? ToolsNew Faucet.Adjustable Wrench.Channel-locking Pliers.Flexible Supply Lines.Basin Wrench.Tape Measure.Plumber's Putty. What tools do I need to change a bathroom faucet? Things you'll need:Basin wrench.Adjustable wrench.Plumber's putty.Bucket.Bathroom faucet and package contents.Rags/towels.Silicone caulk.Knife or putty knife. Is there a...
Guidelines

Can my p-trap be angled?

Can my p-trap be angled? A sideways p-trap is useless, you might as well connect it straight line. Take for example this P-trap connection at a Garbage disposal. At first glance it looks almost normal, when actually it is installed backwards. Well eventually the trap will clog up with debris and water will just not drain properly. Are showers supposed to have P-traps? According to regulations, all shower drains are required to have P-traps. This includes all fixtures connected to a building's main plumbing system. P-traps are curved pipes installed under showers and drains of all kinds. This pipe really...
Miscellaneous

Can a combi boiler be moved?

Can a combi boiler be moved? Average cost to move a combi boiler Combi boilers are the easiest systems to move, especially if you have no water tank. You'll still face costs for pipework, installing the flue and making good space, but overall these are the simplest option. On average, moving a combi boiler costs £500. Does a new boiler have to be on an outside wall? Your boiler should be installed inside a building and can be fitted to any suitable wall strong enough to take its weight when full of water. The boiler's flue must be able to...
Lifehacks

What to do when hot water dribbles out of kitchen faucet?

What to do when hot water dribbles out of kitchen faucet? Try disconnecting the supply tube at the shut-off valve under the sink and holding a rag over the valve while you turn it on and off 2 or 3 times. Scale may be blocking the valve. Why does cold water trickle out of my faucet? Also you can put a penny or dime in the faucet aerator and run the cold water backwards through the hot side for it to come out the hot supply tube connection. Have a bucket. It's usually the washer on the shut off valve....