May 2021 - Page 1198 of 1341

Why is my Kenmore refrigerator humming?

Why is my Kenmore refrigerator humming? The compressor on the refrigerator may get dirty over time, causing a humming sound during operation. To resolve this situation, disconnect power to the refrigerator and remove the panel in the back. Use a soft brush to clean the condenser fan and the compressor. Replace the panel, and restore power to the unit. Why has my refrigerator started humming? Basic refrigerator/freezer maintenance involves the cleaning of the condenser coils on the back of the appliance. When the coils are covered in dust it will overwork itself trying to cool down the inside of the...

Tips

How do you fix a big burn hole in carpet?

How do you fix a big burn hole in carpet? Large BurnsCut around a large burned area, using a craft knife. Position the cutout section on top of the spare carpet. Vacuum the area where the carpet was cut to remove dust, debris and fibers. Apply carpet adhesive to the hole and lay the replacement carpet piece in place. Can you repair a burn in a carpet? Use a pair of small, sharp scissors to cut off burnt carpet fibers. Professional carpet repair can be expensive. The low spot won't be noticeable when the carpet dries. If there is a...

Guidelines

How much does it cost to replace water pump and tank?

How much does it cost to replace water pump and tank? Typical overall well pump and pressure tank replacement cost examples. The retail price for the parts alone depends on what you had installed but could run between $300. to $1400. This leaves your labor cost running between $1700 at the low parts-cost end to $600. How often should a water pressure tank be replaced? First, the quality of the pressure tank itself. Cheaper pressure tanks will last 5 years, while high quality pressure tanks could last up to 30 years. If the water is clean and the tank is...

Q&A

What are the three wires on a 3-way switch?

What are the three wires on a 3-way switch? With a three-way switch, three wires connect the pair of switches—two black “traveler” wires and a third “common” wire. When the circuit's power is turned on, any of these may be “hot,” depending upon how the switches are toggled. Does it matter which wire goes where on a 3-way light switch? A standard 3-way switch features four terminals, each represented by a colored screw. These are the traveler terminals. It doesn't matter which traveler wire (red or black) connects to which traveler terminal as long as it's the same in both...

Guidelines

Why do you need Paslode portable finish Nailer?

Why do you need Paslode portable finish Nailer? It gives great maneuverability to place the nail exactly where you want it wherever you’re working: overhead, on ladders or on your knees. Our portable finish nailer, finish nails and fuel cells are designed to work in tandem so you get the job done right, right away. Non-stop accuracy. Fits in tight spaces. Can a Paslode nail gun be used with straight brad nails? Each machine is compatible with certain types of nails, gas, etc. For example, the IM65 can only be used with straight brad nails. You can check which accessories...

Miscellaneous

Why is my furnace not reaching temperature?

Why is my furnace not reaching temperature? A lack of airflow can cause your furnace to stop heating before reaching the set temperature. Check that registers are open, no ducts are damaged or crushed and replace your furnace filter. Inside your furnace should be clean and free of debris, especially around the blower motor and the heat exchanger. How many degrees does a thermostat drop before the furnace kicks on? First, the user sets the room's desired temperature within the range of the thermostat's scale. When the room temperature drops below this setting and the temperature sensor compares it to...

Tips

Why is my washer shaking so much?

Why is my washer shaking so much? Your washing machine needs to stand level and balanced on its feet to function properly. An unbalanced appliance will vibrate and shake during operation. Try rocking the appliance from side to side or back and forth. If it's rocking a lot, your flooring or appliance's feet may be uneven. How do you know if your washer suspension rods are bad? If one or more of the suspension rods are broken, the washer will vibrate or shake. If a spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation....

Trending

What to do if fire alarm goes off but stops?

What to do if fire alarm goes off but stops? First, try the reset button on each smoke alarm. If that doesn't work, flipping the circuit breaker off and back on might stop the noise. If all of that fails, your ultimate solution may be to disconnect the smoke alarms and remove their batteries one by one. What does it mean when your fire alarm goes off and then stops? Smoke alarms may give off a false alarm if the battery life is fading or if it isn't properly connected. To check the battery, remove the outer casing and check...

Q&A

How do you reset a microwave profile?

How do you reset a microwave profile? 1 Answer. Press the “Off/Clear' button to cancel anything on the display, and reset the microwave. This is a soft reset and will simply get you out of any program you have started. Press it when the cooking complete reminder appears on the display, for example, and the “Your Food is Ready" message will disappear. Why is my new GE microwave so loud? If your microwave is making an unusual or loud humming noise, you may have a problem with the magnetron. This component is part of the high voltage circuit and provides...

Q&A

Can a microwave door be adjusted?

Can a microwave door be adjusted? Best Answer The only safe answer is to take the oven to a shop that repairs these ovens. If the door is crooked enough that it's not engaging the interlock properly when shut, you likely have a microwave leak too. Why is my microwave door so hard to open? If the door on your microwave oven won't open, you may have a problem with the door latch lever. Unplug the unit and remove the cover to access the door latch lever. You may also need to remove the control panel to gain better access....