How do I reset my he3 washing machine?

How do you reset a Kenmore Elite he3 washer?

Press the “Stop” button twice, and then press the “Power” button.
Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
Press the “Start” button to complete the reset process and restart the washing machine.

Why do I have to unplug my washer to restart it?

This is an indication that the door switch is malfunctioning, and not telling the control that the door has been opened. If you don’t open the door the control won’t start another cycle. The only thing you are doing when the power is off is to reset the controls memory.

What does it mean when a washer stops working?

Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.

Can you unplug and replug a washing machine?

The plug should be fine – unless of course it gets trodden on or something whilst not plugged in. And as another responder (George) pointed out, occasionally replugging helps remove any corrosion or contamination buildup, and is a good thing to do.

What should I do if my washing machine won’t drain?

What to Do When Your Washing Machine Won’t Drain

Perform a Master Reset. Unplug your washer for about one minute.
Test the Lid Switch Assembly.
See if the Drain Hose is Kinked.
Check the Drain Hose or Pump for Clogs.
Clean out the Coin Trap.
Check the Water Level Control.
Schedule Washing Machine Repair.

Why does my top load washer not turn on?

Drive Motor. Both top and front load washers use a motor that spins and agitates. (A top load washer uses a reversing motor) The motor spins in one direction to agitate and the other direction to spin. When the wash motor will not turn on it may be faulty.

What does it mean when your washing machine wont start?

This pin or pusher (when lid is closed) will press the lid switch. If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad.

What kind of motor does a top load washer use?

Both top and front load washers use a motor that spins and agitates. (A top load washer uses a reversing motor) The motor spins in one direction to agitate and the other direction to spin.

How can you tell if your washing machine is at fault?

The only way to determine if the control board is at fault is to visually inspect it. Check for burned areas or any component on the board that may look burned or damaged. If you find burned areas or components on the control board, remove and replace it. NEED WASHER PARTS? Over 6,000 New and Discounted Washing

Why is my Kenmore Elite He3 washing machine not working?

The washer requires the use of the recommended amount of High-Efficiency (HE) detergent. Use of regular detergent, or too much HE detergent, will create an excess of suds, in which case an automatic suds detector will cause the washer to enter a suds removal cycle, delaying the wash cycle completion.

What to do if your Washer has no power?

The first step is to unplug the washer, you will plug it back in later. At the back of the top panel on the washer there are three screws that hold the lid on. Remove the screws and then push the lid back about 3/4’s of an inch, the lid will them be able to be lifted off. Look at the area where the cord that plugs into the wall enters the machine.

What does Sud mean on Kenmore Elite He3 washer?

Sud — an excess level of suds has been detected, and the washer is trying to rinse them away. FH — Not enough water entering from the supply hoses. F02 — Drain blocked, kinked, drain filter plugged, or drain pipe exits too far above the washer. FdL — Door lock failure. F11 — Communications between the front panel and control unit are failing.