What does F3 mean on my Kenmore oven?

open oven sensor probe
The “F3” fault indicates an open oven sensor probe or an open sensor circuit. The oven temperature sensor is no longer available. The oven temperature sensor circuit also has thermal fuse connected in a series circuit in one of the two wires in the sensor circuit.

Why does my stove keep saying F3?

When an F3 error code flashes, it generally means that the oven sensor has encountered an error and needs to be replaced. According to Repair Clinic, the error means that a circuit has been exposed or broken.

How do I reset my Kenmore oven?

How to Reset a Kenmore Elite Stove Oven

Press the “7” button on the Kenmore Elite keypad.
Continue holding the “7” button for at least six seconds until a single beep sounds.
Press the “Start” button on the keypad once. This will reset the oven back to the factory default settings.

What does F2 mean on a Kenmore oven?

The “F2” fault code indicates the oven got too hot. Let the oven cool down before reconnecting the power cord. If “F2” displays when cold, this could indicate a faulty electronic oven control board or a faulty oven temperature sensor probe.

Where is the temperature sensor in my oven?

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary.

What does the code F3?

Meaning of Code When the stove has an error, it kicks out a code on the display panel that starts with an “F.” For the F3 error code, this commonly means that oven sensor is bad. In fact, you can do some troubleshooting first to determine if the oven really needs the sensor replaced.

What does F3 mean on a washing machine?

water supply issue
If the washer is displaying error code F3, the washer has detected a water supply issue or an internal problem. F03. There may be a problem with the pump or pressure switch, attempt a Hard Reset. Hard Reset. In some cases the control can be non-functioning or may not accept activation from the control panel.

Why does my oven beep and say F10?

F10 is a common error code for several manufacturers that appears when your oven exceeds the temperature you set it at in either the cook cycle or the clean cycle. A defective temperature sensor can also cause this problem.

What does F3 mean on a Kenmore oven?

If you are experiencing an “open oven temperature sensing circuit” code, be sure to locate and test any fuse in the circuit. In most ovens, F3 indicates an open sensing circuit, and F4 indicates a shorted sensing circuit. Usually a “high oven temperature” code means the temperature sensor or ERC is bad.

What to do if your oven has a F3 code?

Turn on the heat to the oven; if the F3 error code returns, turn off the electricity to the oven again or turn off the gas supply by closing the gas cock at the oven’s gas supply tube.

What should the Ohm reading be on a Kenmore oven?

At room temperature the ohm reading should read within 10 percent of 1,100 ohms. If the reading is higher or lower than that, replace the sensor. If the sensor tests OK, check for any disconnected, broken or burnt wires in the rear of the range.

How to diagnose a Kenmore oven error code?

7-1 DIAGNOSIS. THE FIRST STEP in diagnosing ANY oven error code is to attempt to reset the logic board. Press any “stop,” “reset,” “clear” or “off” button, wait for a few minutes and remove power from the unit, either by unplugging it or turning the breaker off for a few minutes.

Why does my Kenmore oven show the F3 error code?

The F3 error code indicates that the EOC (Electronic Oven Control board) senses a problem with the oven temperature sensor. You could have a defective sensor, a failed EOC or a bad wiring connection between these 2 components. Normally, a technician is needed to diagnose and repair this type of failure.

What does F3 mean on a double oven?

In most ovens, F3 indicates an open sensing circuit, and F4 indicates a shorted sensing circuit. Usually a “high oven temperature” code means the temperature sensor or ERC is bad. However, this symptom can be caused by oven element relay contacts that have “welded” themselves shut. Most double ovens have two control boards.

Where is the temperature sensor on my Kenmore range?

Oven temperature sensor is bad (this is located inside the oven cavity at the upper left rear corner). The oven sensor should be disconnected and tested for resistance and compared with the “RTD” scale.

What does the F1 code on my oven mean?

The “F1” fault code indicates one of the following possible failures: Shorted keypad which is part of the Electronic Oven Control (EOC) Failed Electronic Oven Control (EOC) Oven temperature sensor is bad (this is located inside the oven cavity at the upper left rear corner).