How do you remove jets from a Kohler Whirlpool?

This can be done with the KOHLER ® jet removal tool included with new jets. NOTE: A special tool is provided with replacement jets and with trim kits. This tool allows you to remove the jets from the whirlpool. NOTE: During jet removal, the nozzle must be pointed up or the tool will slip off.

Can you change the Jet trim on a whirlpool?

However, you may want to change the color of the jet trim in your whirlpool. This can be done with the KOHLER ® jet removal tool included with new jets. NOTE: A special tool is provided with replacement jets and with trim kits. This tool allows you to remove the jets from the whirlpool.

How do you install a jet in a whirlpool?

Carefully insert the jet into the housing, then lightly push and rotate the jet until it snaps into position. Do not force the jet. Verify the jet is installed correctly. The jet should turn smoothly both clockwise and counterclockwise.

What should I use to clean my Kohler jet tub?

Kohler does have a jet tub cleaning page. Have you tried their recommendation? Add 2 teaspoons of a low-foaming, powder automatic dishwashing detergent and 20 ounces of household bleach (5% to 6% sodium hypochlorite) to the water. Here is a link that might be useful: Kohler – Flushing Your Whirlpool

Where can I find the model number of my Kohler Bath?

The purchase invoice will list the model number of your bath product. Depending on the bath style, the front cover of the installation guide may include the model number. If the purchase invoice or installation guide is not available, contact the Customer Care Center at 1-800-4KOHLER for assistance.

What is the model number for a whirlpool bubble bath?

The model number for a BubbleMassage bath (or air bath) contains the letter “G” after the base model number. For example, model number 1947-GRA-0 is a bath that has airjets (G) with a right-hand drain (R) and an apron (A). In this example, the “0” is the color code for white.

How long to run whirlpool jets to clean jetted tub?

Run the whirlpool jets like you would when you take a bath. This helps the cleaning solution circulate throughout the tub and clean out the jets. We recommend running them for about five to ten minutes, depending on how thorough you want to clean.

Where can I find the correct Kohler part?

Find the correct Kohler Genuine Part by entering your Kohler product number or name. Tip: Did you purchase your product on Kohler.com? Great! Check Order History to find your product number.

How do you remove a jetted bathtub?

Turn off the water in your home. Because you are removing a jetted tub, you will also want to turn off the power to your bathroom. Unscrew the drain from the bottom of the tub with a basket wrench or screwdriver. Remove the access panel from the tub.

What to keep out of a Kohler whirlpool bath?

DO NOT use attachments not recommended by the Kohler Co. Keep small objects such as bath toys and bathing accessories out of the whirlpool while the pump is operating. NOTE: Whirlpool action can cause even a small amount of bubble bath, bath soap, shampoo, or bath oil to foam excessively.

What to do if there is no water in your tub?

If no water is entering the tub, repair your plumbing supply line problem as you would any faucet in your home. Follow the steps below to create an access panel if making the supply line repair requires access under the faucet and you do not have it. Look for leaks when the tub is filled with water.

Can you remove an old tub and install a new one?

Removing an old tub and installing a new one may seem daunting, but if you carefully prepare and work with a helper, you can complete this DIY project in one day. This guide will teach you how to remove your old bathtub and install a new one. Wear protective eye gear and gloves when removing any kind of tub. You may also want hearing protection.

Can a tub be repaired without an access panel?

The task of gaining access depends on which mechanical part of the system failed and the tub’s location inside or outside of the home. Some repairs may be made without an access panel, but if you need to get to the pump or plumbing you will need access from below the tub or its surrounding sides.