How do I synchronize my pool lights?
How do I synchronize my pool lights?
To re-synchronize your lights, turn the switch on, then back off, then wait between 11 and 14 seconds and turn the switch back on. When the lights come back on, they should enter program #1, and be synchronized. Refer to the included color card as a quick reference to the available programs.
How do you turn on outdoor pool lights?
Much like any other light in your home, the most common way to control your pool light is with the use of a traditional ON/OFF switch. You can simply flip the switch up or down to turn on or off your pool light.
How do I sync my Intellibrite pool lights?
Go to: Menu>Settings>Circuit Functions> Aux (the one the lights are connected to)> Set to Intellibrite. The delay in the pool light sounds like color swim mode was activated and would be normal in that instance. To sync the lights, open up the transformer and disconnect one of the lights and leave the other connected.
How many lumens does my pool need?
According to section 4.6. 1.5. 1 of the Model Aquatic Health Code, “Underwater lighting, where provided, shall be not less than eight initial rated lumens per square foot of pool water surface area.”
How many lights should you have in a pool?
How many lights do I need? The amount of lights you need depends on the size of your pool. For larger pools, two is the minimum recommendation, with three lights being a common amount. Pools smaller than 30′ can be illuminated with a single light, but two lights may be preferable.
Why won’t my pool lights change color?
Some pool lights that change colors rely on small motors that rotate a multicolored lens so different portions of the lens filter the light being emitted by a single bulb. These lights are susceptible to motor failure, which will allows them to function normally but without any color change.
How often do pool lights need to be replaced?
Your pool lighting should give you few problems overall. Most incandescent bulbs will burn for 1,000 hours before bulb replacement is necessary. LED bulbs can burn for 25 years or more (or so they tell us).
How does X10 work in a smart home?
X10 carries a signal over the mains power wiring in your home so you can control light switches, lamp holders or mains outlets. X10 allows you to control these locally or by remote control.
What can I do with the X10 Universal module?
The X10 Universal Module can either close a contact when you send an On signal or keep it closed until it receives an Off signal. As well as sprinklers and drapery, you can control a number of other applications including window openers, speakers security devices, telephones, electronic ignition fireplaces and furnaces.
How many devices can a X10 controller handle?
Sensor modules help you deal with temperature, light and motion. Thermostats and audible alarms are common device modules. Some X10 controller are extremely basic while others are much more complex. A rudimentary controller can cope with multiple X10 devices at 4 sequential addresses from 1-4 and 5-8.
When did the X10 home automation system come out?
A timer and wall switch module soon followed and X10 was fully up and running. The 1980s saw the introduction of a computer interface (CP-290). At the midpoint of this decade, BSR faded into oblivion with X10 (USA) stepping in.
What do you need to know about X10 home automation?
X10 is a versatile home automation technology that uses your home’s existing electrical wiring to remotely control lights, appliances, security systems, pools and much more.
How does a X10 control a light switch?
When you want to control your X10 enabled light switch, you simply press the on/off or dim/bright switch on your controller, and the X10 device responds. You can independently control up to 256 devices in your home. In order to do this, a device is assigned a house and a unit code.
How does X10 work on a power line?
The Details Ultimately how X10 works is by sending an X10 signal out over your homes existing powerlines. The X10 receivers (like switches, appliance modules, etc) wait to hear their signal on the power lines and then respond.
What are the components of a X10 control system?
A Basic X10 System Includes A Transmitter & Receiver Start with X10 Transmitters: Transmitters are control devices that send X10 signals through your home’s electrical wiring to X10 Receivers.