How do you unclog an Upflush toilet?

To clean your upflush toilet, pour 1-2.5 liters of non-acid Toilet Cleaner and Macerator Descaler into your toilet bowl. Switch on the macerator pump for a few seconds to enable the descaler to enter the macerator. Switch off the macerator again and allow the descaler to work for 2 hours.

How do you unblock a macerator pump?

To unblock the macerator, a technician will first turn off the power supply. They will then remove the lid of the macerator. The blockage will most likely be toilet paper or other waste that has become stuck in the blade.

How do you unlock a Saniflo?

Clear any blockage from the inside of the pipe using warm water or a plumbing snake. Unscrew the screws at the base of the Saniflo. Pinch the two ends of the metal clip on the connector between the Saniflo and the toilet to loosen it. Pull the Saniflo free from the back of the toilet.

Why is my macerator not working?

There may be a blockage in the macerator, pump or the waste outlet pipe. Alternatively, there may be a fault with the return valve or damage to the unit’s rubber membrane. Occasionally, this is caused by the microswitch misfiring.

Can you plunge a macerator toilet?

Can you plunge a macerator toilet? If you have a blockage with your Saniflo or macerator toilet it’s not as simple as using a plunger to unblock it. Using a plunger on a macerator toilet could damage the macerator system so if there is a blockage it will need to be taken apart and cleaned.

Can you plunge a pump toilet?

A macerator grinds solid waste into small enough particles that it can travel through your other waste pipes. Because of this, if you get a clog or blockage in your Saniflo, you cannot simply plunge the toilet to unblock it or you may damage the macerator.

How do you clear a Saniflo blockage?

If the return valve is blocked, then you will find that the pump is flushing waste out of the Saniflo, but the waste is then returning as it hits a blockage. To clear this, simply take your thin-nosed pliers, remove the lid of the Saniflo and clear any blockage from inside the return valve.

Can you use a plunger on a macerator toilet?

Using a plunger on a macerator toilet could damage the macerator system so if there is a blockage it will need to be taken apart and cleaned.

Can you adjust the water level in a Saniflo toilet?

The water level in the bowl is limited by the height of the internal trap down stream from the bowl. There is no adjustment possible. If the problem is odors, you can either flush more often, turn on the exhaust fan, or buy a different brand or model of toilet.

Why wont my Saniflo stop running?

My Saniflo keeps running and will not switch off. One of the most common issues with Saniflo pumps is that they occasionally fail to switch off. A blockage in the Saniflo waste pipe leading outside. The pump’s rubber membrane is damaged.

How do you break a macerator?

There are several ways of removing and recovering a Macerator with varying degrees of success. By Pickaxe – Destroys Macerator, returns a Machine Block 100% of the time. By Wrench or Electric Wrench in normal mode – Returns Macerator 80% of the time, returns a Machine Block 20% of the time.

What happens if the power goes out on an upflush toilet?

Of course, no product comes without drawbacks, and upflush toilets have a few: Electricity-dependent: Because the macerator pump runs on electricity, you can’t use the toilet if the power goes out during a storm.

How do you install an upflush toilet tank?

Install the discharge pipe. Place the pump in the tank and mount the float switch. Before sealing the unit, make sure the pump works. Attach a garden hose to a water supply and run it into the flange hole. Connect the discharge to a drainpipe leading to a bucket or floor drain. Tape the temporary drainpipe joints—the pump is forceful.

What’s the difference between a gravity toilet and an upflush toilet?

An Upflush Toilet Is Also Known as a Macerating Toilet Unlike a gravity toilet, which empties into a 3- or 4-inch hole in the floor, an upflush toilet empties out the rear into a holding tank that contains a macerator and a pump.

How tall does a saniflo upflush toilet pump go?

As soon as the water enters the unit, the pressure switch activates the motor to start the pumping process. Once the water level drops the switch deactivates the unit until there is a new rush of water. The unit pumps the effluent upward to 12 feet and/or 100 feet horizontally (with gravity fall).

How does a saniflo upflush toilet system work?

First things first, let’s talk about how a Saniflo upflush toilet system works. The primary difference between a Saniflo system and a standard system is the discharge method. A Saniflo macerating system features two unique components: a macerator and a pump. The macerator includes a rotating blade (think of the blade in the bottom of your blender).

What do you need to install an upflush toilet?

The toilet tank is connected to the water supply. The macerating/pump is connected to the small diameter discharge pipe work. The macerating/pump is connected to the electrical supply. Then optionally connect the discharge pipes from the sink, shower and/or bath. What do you need to install an upflush toilet?