Where can I buy a Beachcomber Hot Tub?

Beachcomber Hot Tubs feature EnviroSkirt maintenance free wood-look cabinets. Hot Tub Outpost carries replacement spa parts for most Beachcomber hot tub models.

Why does my Beachcomber Hot Tub have problems?

A dirty filter can cause all kinds of problems for your Beachcomber hot tub, including cloudy water, decreased water flow, temperature inconsistencies, foul odors and degradation of equipment. To remedy — or better yet, prevent — these problems, clean the tub’s microfilter regularly.

How often should a Beachcomber Hot Tub filter be replaced?

Beachcomber recommends cleaning the filter once every two weeks and replacing it at least once every two years. Some issues — such as sensor problems, a faulty circulation pump or a defective heating element — call for professional assistance.

Beachcomber Hot Tubs feature EnviroSkirt maintenance free wood-look cabinets. Hot Tub Outpost carries replacement spa parts for most Beachcomber hot tub models.

What should the pH level be in a Beachcomber Hot Tub?

Beachcomber recom- mends the following parameters for hot tub water: pH Level 7.2 – 7.8 Sanitizer level (chlorine or bromine) 3 – 5 ppm Calcium Hardness 150 – 200 ppm Total Alkalinity 100 – 120 Total Dissolved Solids not more than 1500 ppm Your dealer may recommend slightly different levels depending on your local source water.

What kind of wiring do you need for a 240V hot tub?

In our movie below, we’ve already poured a level cement slab and placed our hot tub on it. Per the owner’s manual, our hot tub requires a 240V, 50 amp 4-wire electrical hook-up, using AWG #6 copper wire. The electrician is running all buried wiring in 1″ rigid Sch-40 grey PVC electrical conduit.

How do you wire a hot tub to a grounding bar?

Attach the white neutral wire to the spa’s control box directly to the neutral terminal of the GFCI breaker. See our 4-wire diagrams above. Do not attach it to the sub-panel grounding bar. Miswiring it to ground instantly trips the GFCI when energized, cutting power to the hot tub.

When to add sanitizer to Beachcomber Hot Tub?

Add a full bottle of Eliminate #1. Wait one hour. Add 2 oz/60 ml of Eliminate Plus #2. Add 3.5 oz/100 ml of Purezyme #3. Wait 6 hours. Add your sanitizer of choice. Please note: Beachcomber offers several water care programs to suit your needs; ask your dealer for a tote card for those specific details – your startup regimen may vary slightly.

How often should I drain my Beachcomber Hot Tub?

Instead, remove the tub’s cover until the water cools, then press the “Reset” button on the control panel to restart heating. Draining your hot tub at least once every three months helps keep water clean and clear, as does the use of an internal pipe cleaner as part of your hot tub’s water balancing regimen.

How big is a Balboa hot tub heater?

Heaters are flow-through style and can be 5.5kW for the SST-1, SSST-2,SST-10, SST-15 and SST-20 models. This is the Balboa M7 style heater with sensors included. We also offer the Balboa sensors individually if needed.

Where does the Beachcomber Hot Tub come from?

Beachcomber is a hot tub manufacturing company based in British Columbia, Canada. They have been making spas since 1978 and was one of the first spa companies to adapt the vacuum form acrylic. Beachcomber Hot Tubs feature EnviroSkirt maintenance free wood-look cabinets.

Can a cover Guy replace a Beachcomber Hot Tub?

The Cover Guy custom makes all Beachcomber Step Replacement material. Our Beachcomber customers will replace their hot tub step material at the same time as they change their hot tub cover, so The Cover Guy has made that an easy process for all our Beachcomber Hot Tub customers.

Why is my Beachcomber Hot Tub in standby mode?

The blower and pumps activate automatically in spite of the status of the hot tub unit. Means the hot tub unit has entered Standby mode. Check that the Microfilter is in place and secure before depressing any buttons to remove the hot tub unit from Standby.

How does a Beachcomber Hot Tub foundation work?

Beachcomber’s Perma-Seal Foundation elevates and lifts the hot tub off the ground approximately three inches / 7.6 cm. This elevation allows proper water drainage and runoff, without disturbing the integrity of the integrated unit. Made from durable ABS plastic, the kick plate is part of the Perma-Seal Foundation.

Where is the bleed air pump on a Beachcomber Hot Tub?

Bleed Air Pump Relief Valves are located on plumbing lines that are used to allow air to escape. These manually operated valves are generally used during service. Bleeding air with this style of valve is a special convenience found on Beachcomber equipment.

What to do when your Beachcomber Hot Tub is not working?

When you experience weak water flow, indicated by a “DR” error message on your Beachcomber’s control panel, check and open all of the knife valves, the T-shaped handles located on the spa’s pump connections. Pull the plunger up to open each valve, and press it down to close it.

How much does it cost to park at the Beachcomber?

You may pick up The Beachcomber Shuttle at the Shuttle Stop. The Beachcomber will validate for 3 hours of parking with a purchase of $15.00 or more at The Beachcomber Café. Each additional hour after the 3 hours will cost $5.00 per hour up to a maximum of $15.00 per day.

Can you make reservations at the Beachcomber Cafe?

YES! The Beachcomber Cafe is pleased to offer a limited number of reservations through thebeachcombercafe.com. Unfortunately, we are unable to make reservations over the phone or directly at the restaurant. Please visit thebeachcombercafe.com to make reservations for parties of 6 or less.