How to troubleshoot your hot spring spa pool?

Either way, turn the diverter handle (if applicable)slowly 360° (Vista, Grandee GG version, Grandee CC version, Envoy, Siberian, Caspian, Pulse, Flair & Glow models, turn on the 30 amp breaker first, run jets for 10 mins, then the 20amp) My Hot Spring Spa has a blinking red light on the control panel.

Is there an error code on my hot spring?

So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret! Hot Spring ® spa systems are reliable and will last a long time with regular maintenance, but issues do sometimes arise.

Can a jetsetter be used in a hot spring spa?

The Jetsetter is a Hot Spring Spa that sits three very comfortably. You can find Replacement hot tub covers for all Hot Spring Spas models here. “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.

How to turn on Jets in hot spring pool?

HOT SPRING ONLY: For 240 v spas, turn on the 20 amp breaker and run jets 10 mins, then turn on the 30 amp breaker and continue to run jets 30 min. For 120 v spas, plug in and immediately turn on jets for 10 minutes.

Where can I find the hot spring owner’s manual?

Please keep this manual available for reference. If you have any questions about any aspect of your spa’s set-up, operation or maintenance, contact your authorized Hot Spring dealership. They are trained professionals who are familiar with the product as well as new spa ownership concerns.

Why is my hot springs spa not heating?

Why is my Hot Springs spa not heating? • Integrated pressure switch open – check for clogged filters. The integrated pressure switch will reset when the flow of water through the heater has been restored. Contact our customer service team for a service if the heater trips frequently.

What can I do about my hot tub not working?

Pool chemicals and other products can throw off your water balance and lead to damage down the road. Purchase authorized Hot Spring parts from your dealer to ensure that you’re outfitting your spa with quality, lasting components.

How to troubleshoot your hot spring pool and teddy bear pool?

If you have an ozone unit, look for a steady stream of bubbles, if you do not have an ozone unit, look for the curling/rippling of the top of the water. Make sure there is no foreign debris in the spa, pull filters out and replace caps. Run jets 30 min, turn the power to the spa off for 1 minute, and then restore power.

Why is there no power in my hot tub?

Consult an electrician to find the source, if not readily apparent (burnt wires, water, insects or rodent damage, etc.). Some spas and hot tubs have internal fuses, which are meant to blow when voltage spikes occur. These fuses protect your spa equipment, including pumps, blowers and heaters.

Why does my hot spring spa have no power?

Ozone humming is normal. It is the vibration of ozone being sucked through the Mazzi Injector. My spa has no power or is not heating and it is a cold winter day, what do I do? If the spa has no power, or is not heating, place a droplight with a 60 or 75-watt bulb inside the access panel over pump one.

What to do if your hot spring spa lights keep blinking?

Turn power to the spa off for 1 minute, then turn power back on. For 240 v spas, turn on the 20 amp breaker and then turn on the 30 amp breaker. For 120 v spas, plug in. If light continues to blink, Call our Spa Service Department for a service call. 413-594-2666 ext 110 My Hot Spring Spa has blinking Green and Red lights.

Which is the latest hot spring spa relay board?

The 74618 Heater Relay Board is the newest upgraded beefier heater relay board. The original 73355 circuit board was discontinued in 2008. A voltage reading of zero indicates a few other possibilities.

How to troubleshoot a hot spring pool filter?

A quick test to see if the spa filter is the cause: Turn the power off to the spa at the main breaker then take out the filter with the gray knob (make sure that nothing is floating in the spa that could get sucked into the filter area). Turn the spa back on without the filter to see if it begins operating properly.