How do I know what size brake shoes I need?

Expert Reply: To determine whether you need a 10 or a 12 inch brake shoe, you would measure the inside diameter of your brake drum. Depending on the brake assembly, in many instances the cost of a new assembly is the same or just a few dollars more than the replacement brake shoes.

Can you replace drum brake shoes?

They should be identical except for the wear. Brake shoe springs should be replaced with every set of brake shoes. Brake springs lose elasticity like rubber bands and will not hold the brake shoes firmly if worn. Clean and inspect the star wheel.

Are brake shoes interchangeable?

Often times, non-servo or leading-trailing systems will use interchangeable front and rear brake shoes. But, because the shoe is longer than it would otherwise be, it can still provide the same amount of grip as it would if it were shorter but contained less copper.

Are brake shoes the same as brake drums?

Brake shoes are part of a drum brake system. Brake shoes are crescent-shaped components with a rough friction material on one side. They sit inside of a brake drum. Drum brakes and brake shoes are parts of an older type of braking system and have become less common on modern vehicles.

What size are my drum brakes?

Always measure the inside of the brake drum before deciding to discard or machine on a lathe. Use a drum micrometer or an equivalent tool to retrieve these measurements. Compare them to the diameter stamped on the outside of the drum. If the drum is scored or grooved, place the tool into the deepest part of the groove.

How often do drum brake shoes need to be replaced?

The brake shoes on your car are designed to last around 35,000 miles, but in some cases they will not make it that far. There are a variety of things that can lead to increased wear on a set of brake shoes, like damaged hardware or warped brake drums.

Can I replace 50mm brake pads with 70mm?

Yes! You shouldn’t have any issue replacing your existing 50mm pads with these 70mm pads they will just be a little longer than your old ones.

Are brake pads the same for front and back?

Front brake calipers work significantly harder than the rear, which requires them to be a different size to handle the force that is applied to them. The front and rear brake pads cannot be interchanged, as the front pads will not fit on the calipers of the rear and vice-versa.

What are the 2 types of drum brakes?

There are three types of drum brakes depending on how the brake shoes are pressed on to the drums; leading/trailing shoe type, twin leading shoe type and duo-servo type.

How do you change rear drum brake shoes?

Remove the small metal automatic adjuster lever. Release the inner top spring and pull the front shoe away from the backing plate. The rear brake shoe is held to the assembly by the parking brake lever and the parking brake cable. Pop the parking brake cable out of the hook on the parking brake lever.

When to replace the rear drum brake on a Toyota Corolla?

How to replace the rear drum brake shoes and springs on a 2003-2008 Toyota Corolla with picture illustrated instructions. This automotive “how-to” guide was specifically written to assist owners of the ninth generation (2003, 2004, 2005, 2006, 2007 & 2008) Toyota Corolla in replacing the rear drum brake shoes and springs.

Are there any Dorman drum brake backing plates?

Dorman 13867 HELP! Brake Backing Plate . Only 17 left in stock – order soon. . . Only 19 left in stock (more on the way). . . Only 5 left in stock – order soon. APDTY 24978 Brake Backing Plate- 1992-78 Models W/ 9-1/2In. Drum Brakes.

What kind of spring for rear drum brake?

Two other compatible “brake hardware” spring kits include the Raybestos H17378 and Beck Arnley 084-1560. The first steps are to chock the front wheels to prevent the vehicle from moving, slightly loosen the five lug nuts on each rear wheel with a tire iron, raise the rear of the car with a floor jack and securely support it with jack stands.

What is the backing plate for brake shoes?

Vehicle Specific Dorman Backing Plate – Brake Shoe Part Number: 924-214 Warranty: 3 months Notes: Rear. 9.5″, 10.5″ or 11.5″ ring gear.

How are drum brake shoes secured to the wheel?

The shoes are secured to a backing plate by hold-down springs, and actuated by the pistons in a hydraulic wheel cylinder. When the brakes are applied, the linings press against the friction surface of the brake drum, which encloses the assembly and attaches to the axle or hub, turning with the wheels.

Where does the larger shoe go on a drum?

Assuming the bottom of the shoes can float (ie, no anchor pin to the backing plate), then I’ve always learned the larger shoe goes in the rear, not the front. The reason is this: As the wheel cylinder pushes the shoes out to the rotating drum, the shoes want to turn the same way the drum is turning.