Is the Drayton digistat RF3 room thermostat faulty?

My Drayton Digistat RF3 Wireless room thermostat is about 13 years old and has no display. Changed the batteries but still no display. The receiver shows a static red light. Tried recommissioning but still no display. Is the the room thermostat faulty or have I mucked up the receiver by recommissioning?

Is the Drayton digistat powered by AA batteries?

The Drayton Digistat is a digital thermostat for your home. The digital interface on the thermostat is powered by two AA batteries. If the batteries drain down, you’ll notice a “Low Battery” warning and you’ll be unable to control the thermostat. Replace the batteries as soon as possible to prevent such an occurrence.

Do you have a Drayton digistat rf701 + 3RF programmer?

We have a Drayton Digistat RF701 +3RF programmer. The receiver just showed the red light so we ordered a replacement and it still shows red light continually. We changed the batteries in the programmer and it shows display does it need changing, if so with what0 Try re-pairing them. If no joy you will need to replace the thermostat part.

How do you turn off the red light on Drayton digistat?

Push and HOLD IN the buttons on the SCR IN THE ORDER 1 followed by 2, until the red light goes off. Put the batteries back into the holders on the RF1 and CLOSE THE RIGHT HAND HOLDER BEFORE THE LEFT ONE. After a short delay, the red light on the SCR should start flashing at about 2 flashes / sec.

How do you change battery in Drayton digistat?

Slide the first battery out of the compartment, and then slide the second battery forward and out of the compartment. Insert one battery into the compartment. The “Plus” side of the battery should be facing right. Push it to the left to move it to the rear of the compartment. Insert the second battery. Again, the “Plus” side should be facing right.

What kind of battery does digistat + 2RF use?

When the batteries start to run low a battery icon will flash in the display, to indicate “low battery” during this time the Digistat +2RF will function normally (see fig 1). Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.

Are there different models of Drayton digistat SCR?

Any suggestions would be gratefully received. There are 3 models of radio Digistat: RF!, RF2 and RF3. It sounds like you’ve got the RF3 that some people consider to be about as user-friendly as a cornered rat. A new RF1 will do exactly what you say you want and it and the new SCR will fit straight onto the existing backplates, so no wiring to do.

What should I do if my Drayton digistat catches fire?

If you now press the plus button to increase the setpoint, the SET message should flash on the RF1 display and a little flame image should appear to the left of the temperature display. Very soon after that, the red light on the SCR should flash some more and then the green call-for-heat light should come on too, and the boiler should fire.

Is the Drayton digistat more advanced than Worcester unit?

The Drayton unit has programming features that are more advanced than the now 8 years old Worcester unit. Thanks A: Yes they are. Q: I have a digistat +3rf thermostat and receiver, but the lcd display has gone on the thermostat. Can I simply replace the thermostat and it will ‘talk’ to the current receiver, or do I need a new receiver too? Thanks.

Are there any manuals for the Drayton rf601?

User Manuals, Guides and Specifications for your Drayton RF601 Thermostat. Database contains 2 Drayton RF601 Manuals (available for free online viewing or downloading in PDF): Installation manual .

How do you troubleshoot a digistat RF receiver?

A) Pull down battery drawers from Digistat unit and allow screen to go completely blank B) Turn off the power supply to the SCR receiver unit and leave for 5 seconds C) Turn on power to SCR unit and check red light is on D) Put the SCR unit into its manual override mode by pressing the override button No.2 once.

Can a digistat be used with a 1rf?

At present it is used with a Digistat+1RF Yes it will. We have a Drayton Digistat RF701 +3RF programmer. The receiver just showed the red light so we ordered a replacement and it still shows red light continually. We changed the batteries in the programmer and it shows display does it need changing, if so with what0