Info

The hedgehog was engaged in a fight with

Read More
Lifehacks

How much does it cost to rebuild a rear differential?

How much does it cost to rebuild a rear differential?

Depending on the make and model of your car, as well as its condition, expect to spend between $1,500 to $4,000. The other factor is if you buy a new rear-diff or a used/rebuilt one.

Is a GM 10-bolt rear end good?

That’s usually proven when used in high-performance, high-horsepower applications. But for all intents and purposes, the 10-bolt rearend is a great unit for a street/strip car, and can be stout enough to handle even the occasional abuse delivered by use at the racetrack.

How much does it cost to rebuild a rear end on a truck?

Complete Replacement. A typical rear differential repair costs anywhere between $200 and $400. These typical repairs would include your bearing, seals, and fluid changes. Of course, when a gear change is required, that’s when things get pricey. $1,500 is just the minimum you can expect to pay for new gears.

Are all GM 10-bolt rear ends the same?

That is the great caveat; there are four sizes of 10-bolt GM rear ends: 7.5/7.625-, 8.2-, 8.5-, and 8.6-inch. These sizes refer to the diameter of the ring gear, and the one you use makes a big difference in the performance potential.

How hard is it to rebuild a rear differential?

A complete rear differential replacement includes replacing the housing, gears, bearings, and seals. The average time it takes a certified mechanic to perform a differential rebuild at a shop is usually three to five hours. A rebuild on a commercial vehicle by someone without prior experience could take much longer.

What are the signs of a bad rear differential?

Symptoms Of A Bad Rear Differential

  • Vibrations. A bad differential can cause vibrations that increase in intensity as you speed up and reduce as you slow down.
  • Grinding Gears. Grinding gears is another significant sign that your differential is failing and that the gears are wearing themselves out.
  • Whining Noises.

What causes a rear end to go out?

The most common cause of a bad differential is lack of oil, which could result in grinding at high speed, cause the carrier to break, or in most cases, block the rear wheels.

How do I know if my rear end is Positraction?

If you can turn the wheel on your side while the other wheel is held still, the rear differential is not a Positraction unit. If you cannot turn the wheel on your side while the other person is holding their wheel in place, then the axle is a Positraction.

What size is the pinion nut on GM 10 Bolt?

8.5″
PYN10 – 10-Bolt 8.5″; Pinion Nut (30 Spline Pinion)

Is it worth rebuilding a differential?

As long as vehicle owners keep up with maintenance, most vehicles won’t need a differential rebuild during their time on the roads — but, if you are in an accident or do experience a problem with your differential, repairing it is important to your safety and the health of your vehicle on the roads of Madison and …

What size is a 10 bolt rear end on a Chevy?

Although the 7.5-inch 10-bolt closely resembles the 8.5-inch housing, you can positively identify the Chevy 7.5-inch rearend by measuring it. The oval-shaped cover measures 8 5/16 inches by 10 9/16 inches.

When did the GM 12 bolt rearend come out?

It first appeared in 1970 production cars as a corporate replacement for the 8.2-inch 10-bolt rearend. It was used in different models by all GM divisions – with the exception of Cadillac. Since it was so widely used, there is a better possibility of finding one of them at a salvage yard than locating a 12-bolt.

How big is the pinion on a 10 bolt rearend?

The pinion diameter is 1.438 inches, and has 25 splines. Like all Chevy 10-bolts, the axles are retained by C-clips on the inner end of the axle shaft inside the carrier. If you find a rearend that uses a large spring perch like this, it is from either an X or F-Body.

How can I tell what year my 10 bolt rearend is?

Date and location of manufacture are stamped in the axle tube, and this table deciphers the code. Many times, if you locate a 10-bolt rearend, it’s usually a 7.5-inch unit. These have been around since 1975, and were installed under cars, small trucks, and vans up to the 2005 model year.