How do you remove the ignition switch on a Volkswagen Jetta?

Insert small center punch, or an Allen wrench inside the hole. This will press the retaining clip in and allow you to remove the ignition switch assembly.

Why won’t my key turn in the ignition Volkswagen Jetta?

What are common reasons my Volkswagen Jetta key won’t turn? While there are a variety of reasons your Volkswagen Jetta key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

How do you reset ignition switch?

Insert the ignition key and turn it to the on position and then attempt to start the engine (crank over), the engine wont start. With the key still in the run position wait 10 minutes and the security light should blink and then go out. Turn the key off and wait 5 seconds.

Is it hard to replace ignition switch?

Once you’ve been able to identify the ignition switch as the source of your trouble, replacing it is often a fairly straightforward process that requires only common hand tools. You should consult an application specific repair manual before starting this project on your own.

Why isn’t my key turning in the ignition?

The most common reason that a car key will not turn is that the steering wheel has locked. Pull the steering wheel in the direction that has give, and hold it there. Turn the key toward the accessory position while keeping the steering wheel turned. If nothing happens, rock the steering wheel as you turn the key.

How does the ignition work on a VW Jetta?

The Volkswagen Jetta uses an integrated ignition switch to unlock the ignition and start the car. If the switch fails, you won’t be able to start the engine, but the key will still turn. While the switch can be replaced, the job requires basic mechanical skills.

How do you remove the ignition switch assembly?

This should form a cross where the two lines intersect. Drill a 1/8″ hole where the two lines meet on the aluminum housing. Insert small center punch, or an Allen wrench inside the hole. This will press the retaining clip in and allow you to remove the ignition switch assembly.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

What should I do if my ignition switch is not working?

Keep pressing it in until you hear the click of the release pin setting into place inside the steering column. If you don’t hear a click from the release pin, the ignition switch isn’t properly seated yet. You may need to push in on the switch a little to make it click into place. Helpful? Reconnect the battery and test the new switch.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

How do you remove a battery from an ignition switch?

Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.

Where do I find the ignition switch on my car?

Locate the battery in the engine bay or trunk of your vehicle. It will look like a black box with a positive (+) and negative (-) post sticking out of the top of it. Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post.

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.