How do I change the default gateway in Solaris 11?

How do I change the default gateway in Solaris 11?

Change the default route in Solaris

1. Step 1: edit /etc/defaultrouter.
2. Step 2: Delete the current default route.
3. Step 3: Assign the current default route.

How do I set default gateway?

Configuring the IPv4 Default Gateway

1. Go to Control Panel > System > Network > IPv4 > Default Gateway.
2. Under Use the settings from, select an interface that QES will use as the default route.
3. Add a static route. Click Static Route. The Static Route window opens. Specify an IP or subnet address.
4. Click Apply.

How do I set a default route in Solaris?

To flush (remove) the routing table of all gateway entries, use the route flush command. To add a default static route using the /etc/defaultrouter file, add the default router IP address to the file /etc/defaultrouter. A system that is configured with an /etc/defaultrouter file does not execute the in.

How do I find the gateway in Solaris 10?

Check the file /etc/hostname. bge0 , the configured IP address could be in there. By default the hostname is listed in that file and the name is looked up in /etc/inet/hosts . From the found entry, the IP address is used together with the corresponding netmask from /etc/inet/netmasks .

How do you configure IP address in Solaris 10?

Configure IP in Solaris 10

1. Configure and plumb each interface. ifconfig qfe0 plumb up.
2. Assign an IPv4 address and netmask to the interface. ifconfig qfe0 192.168.1.10 netmask + 255.255.255.0.
3. OR.
4. Verify that the newly configured interfaces are plumbed and configured.
5. judi-dev-01 (alias name or the IP)

How do I create a static route in Solaris 10?

Creating Persistent (Static) Routes

1. Use the route command with the –p option to persistently add a route: # route -p add default ip-address.
2. Display the currently active routes on a system by using the netstat command with the following options: # netstat -rn.

How do I create a persistent route in Solaris?

Creating Persistent (Static) Routes

1. Use the –p option to add a persistent route: $ route -p add default ip-address.
2. Use the –name option to add a persistent route by specifying a name rather than destination and gateway: $ route -p add destination-address gateway-address -name name.

How do I change the default gateway in Solaris 10?

How to Change The Default Route or Gateway on Solaris

1. Edit /etc/defaultrouter. -This configuration will apply after next reboot. [root@SolarisServer ~]# vi /etc/defaultrouter 192.168.2.1.
2. Run the following command to delete and add the default route. -This will apply the configuration with immediate effect.

How do I change the permanent hostname in Solaris 10?

So here’s a very simple procedure for updating the hostname of your Solaris 10 server.

1. Step 1: Update /etc/hosts.
2. Step 2: Change /etc/nodename.
3. Step 3: Update /etc/hostname.
4. Step 4: Reconfigure network and reset hostname to the new value.

How do I change the default gateway in Sun Solaris?

If you wish to add or edit the Default Gateway or the Default Router in Sun Solaris, edit /etc/defaultrouter file and update the IP Address. One entry per line for one or more default gateways (very unlikely to have muktiple default gateways).

Why can’t I manage /etc/defaultrouter in Solaris 11?

Because the /etc/defaultrouter file is deprecated in Oracle Solaris 11, you can no longer manage routes (default or otherwise) by using this file. Using the route command is the only way that you can manually add a route to a system. To make the changes persist across reboots, use the –p option with the route command.

How do I change the default route of the default gateway?

Edit /etc/defaultrouter-This configuration will apply after next reboot. [root@SolarisServer ~]# vi /etc/defaultrouter 192.168.2.1 Proceed to change the ip to your preferred/new ip address of your gateway and save. 2. Run the following command to delete and add the default route. -This will apply the configuration with immediate effect.

How many default gateways can be added per line?

One entry per line for one or more default gateways (very unlikely to have muktiple default gateways). This file is read at the boot time and hence the server needs to be rebooted for the changes to take effect.