How do I fix the F28 code on my Whirlpool Duet washer?

An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit. Rebooting the control unit is accomplished in less than 10 minutes, even by the novice.

What does F28 mean on a Whirlpool Duet Sport washer?

central control unit
Posted: 08/01/17. shantapanchu a F28 error code is a common problem indicating that there is a communication problem with the central control unit. Any error code can be caused by a electrical anomaly. try to reset your washer.

What is MCU on washer?

Washing machine motor control board (MCU). The motor control board regulates the speed at which the washer spins. If the motor control board is defective, the washer won’t spin or agitate.

How do you run a diagnostic on a Whirlpool Duet washer?

Duet Washer Diagnostic Test Mode Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)

How do I reset my Whirlpool Duet washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

What is a F25 error code?

The F25 fault code indicates a problem with the drive motor home. The washer shuts down if the control can’t detect the speed of the motor.

How do I fix the F25 code on my Whirlpool washer?

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). Plug in washer or reconnect power. Check the MCU by looking for operations of the drive motor. Check the drive motor for powered rotations.

What does F28 error code on Whirlpool duet washer mean?

What Does F28 error code on whirlpool duet steam washer mean? F28 means that your main central control board (CCU) and the motor control board (MCU) are not communicating with one another properly.

What does F28 mean on a washing machine?

F28 means that your main central control board (CCU) and the motor control board (MCU) are not communicating with one another properly. You will need to check all the connections at both boards, the mcu is in the bottom of the washer and the ccu is mounted at the top inside of the washer on the right side.

Is the Whirlpool duet washer fully electronic?

A Whirlpool Duet series washing machine is a fully electronic washer. The digital display on the Whirlpool Duet washer, at times, will display an error code to alert you of a problem with the washer.

Where is the reset button on a whirlpool duet washer?

Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place. Remove the detergent tray screws using a Phillips screwdriver and pull off the tray. Find the control console unit reset lever and pull it toward you. Replace the detergent tray and secure it with the screws you removed.

What is the serial code on a whirlpool duet washer?

The dreaded “serial communications error” in Whirlpool-built front-load washers appears as various codes, depending on the particular model. On the Old-Skool Duet washers, the most common communications error code was F-11: communications error between the Central Control Unit (CCU) and Motor Control Unit (MCU).

What is the fault code on Maytag duet washer?

On the new model Duet washers, this same error has been re-labelled as F-28. On some Maytag front loaders (all built by Whirlpool, in case you didn’t already know that), you may see an F6E2 fault code, which is a communications error between the CCU and the User Interface (UI) boards.