How do I get the installer code for Vista 20P?

The default installer code on a Honeywell Vista-20P is 4112. If you have lost your installer code, you can alternatively use the backdoor method to get into programming. This is done by pressing and holding the * and # keys within 50 seconds of powering on the system.

How do you program a Honeywell system?

Here’s how to do it:

Unplug the transformer from the power source.
Disconnect the battery.
Plug the transformer back in.
Reconnect the battery.
Within 30 seconds of turning the alarm system on, press * and # at the same time.
Enter *20.
Enter a new 4 digit installer code.
Press *99 to exit programming mode.

How do I factory reset my Vista 20P?

Access the alarm’s programming mode by entering the installer code, followed by “8,” “0” and “0,” into the control panel.
Press the “*” button on the control panel, followed by the “9” and “7” buttons to reset the security system to factory settings.

How do I bypass Vista 20P?

Enter four digit user code (same code to arm and disarm the alarm system), followed by the Bypass (6) key. be bypassed (single digit zone numbers must be preceded by a 0 – example: 02, 03, etc.) The Keypad will momentarily display a Bypass message for each bypassed zone.

How do I get into Vista programming?

During the reboot cycle (within 50 seconds of power up) press and hold the * (star) and # (pound) keys simultaneously for 3 full seconds. If you successfully get into programming you will see “installer code 20” displayed if you have an alphanumeric keypad or “20” if you have a Fixed English keypad.

How do I program Vista 128bpt?

To enter program mode, enter installer code + [8] + [0] + [0] + [0] • To set standard defaults, press *97 • To change to next page of program fields, press *94 • To return to previous set of fields, press *99 • To erase account and phone number field entries, press [*] + field number + [*] • To assign zone descriptors.

How do you bypass a paradox alarm?

Bypassing (Switching Off) Zones on Arming

Press the [BYP] button.
Enter your access code.
Select the zones that you wish to bypass by pressing the corresponding buttons.
Press the [ENTER] button to save the bypassed zone entries.

How do I EXIT programming mode on my vista-20p?

After completing programming, it is important to use *99 to exit. This method allows you to reenter programming using the new installer code next time. **Please note: It is possible to completely lock the Vista-20P from local keypad programming. There are a couple of ways this can be done.

How to enter programming on a vista-20p alarm control panel?

To enter programming on a VISTA-20P alarm control panel, you can either enter your 4-digit installer code followed by [800] or, if you don’t know your installer code, you can power the VISTA-20P down (remove battery backup and transformer) and then press [*] and [#] together within (50) seconds of powering back up.

Can a vista-20p be installed by someone else?

Most alarm companies change the default installer code of [4112] to something different and they do not provide you with the installer code, so if your VISTA-20P was installed by someone else, you will most likely need to use the “backdoor” programming method.

What is the programming guide for Honeywell Vista?

Programming Guide K5305-1PRV8 5/11 Rev. A RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises.

How do I add user codes to a vista 20p, 21ip?

You will get a short confirmation beep, letting you know the command has been successfully executed. User numbers 03 and higher on the Vista 15P, and Vista 10P, and users 04 through 32, and 34 through 49 on the Vista 20P, and the Vista 21iP will automatically be assigned authority Level 0 = standard user, when created.

What do the Honeywell Vista 20p and 21ip do?

The Honeywell VISTA 15P, 20P and 21iP are hardwired security systems that can each serve as the central hub for a user’s security setup. Since these systems do not come with their own display screen, a user may feel somewhat intimidated when working with one of these panels.

What do you need to know about programming in Vista?

In order to perform most of the basic programming functions on a VISTA panel, you must first enter into programming mode. The following are some basic commands that you will enter when programming your VISTA system: Reset Panel to Default (Note: You will lose all programming!)