How do I know if my Hayward salt Cell is working?
How do I know if my Hayward salt Cell is working?
The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochlorite gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!
Why does my Hayward salt Cell say no flow?
The Hayward Aqua Rite has sensed a no flow condition and has stopped generating chlorine. Check that the flow switch is plugged into the connector on the bottom of the control unit and that the wire is not cut or damaged. Make sure you have at least 12″ of straight pipe before the flow switch.
How many amps does a salt chlorinator use?
Most units use between 6.2 Volts dc and 9.2 Volts ac and operate between 10 and 30 Amps.
How long does a Hayward salt cell last?
about five years
This is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced.
How do I know if my Hayward switch is bad?
If the flow switch is stuck closed, when you unplug the wire inside the controller, the producing-chlorine light should go off. If the light does not go off, then the problem should be inside the controller.
Why is my salt cell not producing chlorine?
If your Stabilizer is too low, the pool water will not be able to hold the chlorine being produced and it will appear that your SCG cell is not producing adequately. Likewise, a low pH level will oxidize chlorine faster, making it difficult to maintain the right level of chlorine.
What temperature does a Hayward salt cell stop working?
In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.
When should you clean a salt cell?
You should check your salt cell weekly to ensure that there are no problems and rinse off the plates as soon as you start to see scale formation. Every salt cell should be chemically cleaned at least once per season, usually after the pool has been closed.
Why is the salt level on my Hayward Aqua rite not right?
Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. If the salt cell is clean but the salt reading is off, the Aqua Rite will need to be re-calibrated. The following video will provide a guide on how to recalibrate a Hayward Aqua Rite.
When to call Hayward for a salt cell replacement?
If the salt system settles on a number that is unrealistic, there may be something wrong with your system or salt cell. The most likely issue is that your salt cell needs to be replaced. It could also be that the board in your power center needs to be replaced. At this point you will want to call Hayward at (866) 429-7665.
What should the salt level be in my Hayward pool?
Push the diagnostic button until “T-XX” appears on the display. Step 2: Verify the accuracy of the salt readings (2700-3400 pm) with an independent test kit or by taking a water sample to your local pool store for testing. 3200 ppm is the ideal level. If the salt level is below range, add enough salt to achieve a salt level of 3200 ppm.
Why does the salt reading not match the strip?
The reading is also somewhat affected by the water temperature, generally reading a bit lower than actual when the water is cold. Depending on the time of day and when you looked at the reading relative to when you added the salt, it could do what you describe. Don’t expect the reading to exactly match a salt test strip.
If the salt system settles on a number that is unrealistic, there may be something wrong with your system or salt cell. The most likely issue is that your salt cell needs to be replaced. It could also be that the board in your power center needs to be replaced. At this point you will want to call Hayward at (866) 429-7665.
What should salt level be on Hayward Aqua rite?
Press and hold the diagnostic button for 3 to 5 seconds. The LED light should go out. Your salt level is between 2500-2600 parts per million (ppm). Your chlorine generator is still producing chlorine at the moment, which is a good thing.
When does Aqua logic P4 show low salt?
My experience, 10 years with an Aqua Logic P4, and currently on my 3rd cell, is that I get low salt when the salt is not low for some time before the cell completely dies. So, yeah, probably new cell time for you. You must log in or register to reply here.
Is it normal to have 10 amps of salt in your pool?
The numbers are varying all over the place, which is not what you normally see for a worn out cell. Some variation in the salt level is common enough, but I’ve never seen to go to 10 amps before. Pool store cell testing is usually fairly reliable. Reusing water is normal, shouldn’t make any difference.