How do I remove a Commodore door?

First remove the door stop thats the thingy between the upper and lower hinge , it just unbolts . Use a punch to drive the pins out starting with the bottom one . Punch the bottom pin out up through the top of the hinge and the top pin out through the bottom of the hinge . then remove the door .

How do you remove the door lock on a VS Commodore?

Disconnect the lock cylinder control rod from the door lock by releasing the retaining clip. Withdraw the slide clip from the rear of the exterior door handle. Manoeuvre and withdraw the handle section from inside the door and remove the surround and seal.

How do you remove a VS Commodore speaker?

Remove the mesh cover (work at it until one side pops up, then you can take the other sides out), unscrew the screws, pull the speaker up, unplug. taking out the seats is a waste of time if u only wanna change the speakers.

Are VE and VF doors the same?

The only common parts the VF Commodore shares with the outgoing VE are the door skins, roof and window glass, although Ferlazzo adds that “we did need to modify the doors with new passive-entry door handles, but the form shape is the same..”

How do I remove a door panel?

Before we start, the following image will show you what to expect.
Using a small flathead screwdriver, gently pop off this cover.
Remove this screw using a suitable TORX Driver.
Remove the two screws located on the bottom of the door trim.
Remove the two screws located under the handle.

How do you remove a dashboard from a VE Commodore?

Wedge your fingers behind the lower section of the trim and firmly pull upwards as shown by the red arrows.
With the bottom clips released use a gentle hinging and pulling motion to release the top clips on both sides of the steering wheel.
Be careful releasing the clips as the trim will drop downwards.

How do you remove the inner door handles in a 97 VS Commodore?

no its diff in the vr/vs there are no screws otherwise i woulda had it off already.. ive been told that you need 2 pull across a slide pin from behind the handle and then unclip 2 white clips and the handle bit will come out and then the rest off it just slide out but i can find this slide pin or clips

Can you remove the door trim on a VR Commodore?

To start viewing messages, select the forum that you want to visit from the selection below. Thread: Removing the door trim on a VR Commodore. The only Country in the English speaking World where you cannot sue your Solicitor or Barrister.

How do you remove the window winder on a Commodore?

Now that the window winder has been removed it’s time to remove the arm rest where the electrical mirror switch is. You will see like a plastic cover which is easily removed either using an o-ring pick or flat screwdriver.

How to remove front door trim on VN-VS?

You will see like a plastic cover which is easily removed either using an o-ring pick or flat screwdriver. Once removed disconnect the electric mirror switch and remove the two phillipshead screws (one at the top and one at the bottom). Once done the arm rest should pull away without too much trouble.

How do you remove a front door lock on a Commodore?

separate the lock cylinder wiring connector and cut any cable ties securing the wiring to the lower door panel. Disconnect the lock cylinder control rod from the door lock by releasing the retaining clip. Withdraw the slide clip from the rear of the exterior door handle.

How do you replace a door window on a Commodore?

Once you have the new window down inside the door, then it will take some maneuvering of the inner track to get both the inner slides to engage. Once the slides are engaged and the inner track is bolted back in to place with the three bolts the window will slide up and down freely, with no support from the regulator.

Can a transfer vent be removed from a Commodore?

The transfer vent can be tricky to get out but don’t go using too much force as it may break. Now the next thing is to remove the vents, this can done with a flat screwdriver with a bit of cloth or rag wrapped around it to prevent any damage or at least minimise any damage as screw drivers can slip.