How do I reset my GE water softener?

START A RECHARGE Press the RECHARGE button and hold for three seconds, until “RECHARGE NOW” begins to flash in the display, starting a recharge. This recharge draws the sanitizing bleach or brine into and through the water softener. Any air remaining in the water softener is purged to the drain.

Why is my GE water softener not working?

Your GE water softener needs power to work. If it has come unplugged accidentally or if a fuse or circuit breaker has blown, then it won’t be getting any power. Solution: Check that your unit is plugged securely into the outlet. If it has then you need to replace the fuse or flip the breaker switch back on.

How do I know if my GE water softener is working?

How To Tell If Your Water Softener Is Working: The Soap Test. Another easy way to check for a malfunctioning water softener is to see if your soap lathers and bubbles. Pure liquid soap (such as Castille) will do this when mixed with soft water. If the water is hard, the same soap won’t function properly.

Why is my water softener not working?

Water must flow into the brine/salt tank and then back out for the water softener to do its job. If water is not entering the tank, perhaps the float switch is stuck or there is a clog in its tubing. If cleaning doesn’t fix the problem, the float mechanism will have to be replaced.

How much water should be in my GE water softener brine tank?

How much water should be in brine tank after regeneration? In simplest terms: The Control Valve should be adding 3 – 4 gallons of water at the end of regeneration process ( Brine Refill ). A level of 6 – 12 inches, depending on the amount of salt in the brine tank, and the shape of the brine tank ( square or round ).

What to do if water softener is not working?

To get your soft water flowing again, here are three fixes you can easily perform.

Fix 1. Clean the brine (salt) tank: Make sure the salt hasn’t formed a hard dome or crust inside the brine tank.
Fix 2. Clean an iron-fouled resin bed:
Fix 3. Clean the resin tank injector:

Should there be water in my brine tank?

The brine tank is the part of your water softener that holds the salt. Your water level should always be slightly lower than your salt level in your water softener brine tank. That is why it is important to always make sure that your water is lower than the salt.

What is a good water hardness setting?

7–11: Hard water is packed with minerals at 7–11 gpg, and you likely deal with crusty faucets and pipes and possibly reddish rings on your porcelain from excess iron. 11–15: Considered very hard, water at 11–15 gpg exhibits all the signs of hard water all the time. 15+: Extremely hard water is anything over 15 gpg.

What does the hardness setting on my water softener mean?

The hardness setting is a number that is determined by the “grains” of hardness in your water and the iron content. You cannot set how hard or soft you want the water. It is either hard or soft–no adjustment for in between.

What to do if your GE water softener is not working?

This softener features a recharge countdown, six-hour memory (in case of a power outage) and an electronic diagnosis system. If your GE water softener is not working effectively, try troubleshooting it before calling an expensive repair person or replacing the system. Check the water softener’s power supply.

Why is my Kenmore water softener not lighting up?

Lack of electrical power, a failed power transformer or a faulty timer can prevent the water softener display from lighting up. Check the electrical outlet by unplugging the water softener and plugging a small lamp or appliance into the outlet to check for power.

How can I check the power of my water softener?

Check the power of the water softener: Most water softeners use electricity to run a timer that regulates the regeneration schedules. Make sure the conditioner’s voltage transformer is installed correctly, plugged in, and working.

How long does it take for GE water softener to recharge?

Push the “Recharge” button on the top of the softener. Hold it for 3 seconds. Once the display begins to flash “Recharge,” wait about 2 hours for the unit to finish the sanitization process. Check your home’s water pressure.

What to do if your water softener is not connected?

Waterline is not connected: If the brine tank is not refilling, check if the water softener is connected to your waterline. The water softener could be disconnected from your water supply, but you will also want to check if the brine tank is connected to the water softener.

How can I Turn Off my water softener alarm?

The alarm can be turned off by pressing any button but the blue indicator light and display will flash. If an electrical spike takes place from an incoming power line in your home, disconnect the power, unplug the power transformer from the wall outlet and wait for several minutes, then plug the transformer back in.