How do I reset my Jandy AquaPure?
How do I reset my Jandy AquaPure?
Turn off the system and unplug the little board and then reinstall it. Turn on the system, wait for about 5 minutes, and then hold the little white button for 5 seconds. This will calibrate the sensor.
How do you clean AquaPure?
Add one pint of muriatic acid to two quarts of water in a bucket. Pour the solution into the cell so it begins to foam. Leave the solution in the cell until the foaming has stopped or until the solution has been in the cell for more than 30 minutes.
How do I calibrate my Jandy AquaLink?
Press and hold the ‘Pool Temperature’ (‘D’) key for 15 seconds. The system will beep when the button is pushed, it will beep again after 10 seconds, and again after 15 seconds. Release the key after the third beep.
How do I test my pool Temperature sensor?
The sensor can be tested with a multimeter. It should read 10,000 ohms at 77F (25C) degrees. You can lookup other test values in the Temperature vs Resistance Conversion Chart for 10k Thermistors.
What is the code for Jandy aquapure power supply?
1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3. How To Change a Jandy AquaPure Tri-Sensor Front board power supply is either too low or too high. 1. Generates code 173- Low input voltage, IF code 188 is present.
What is code 172 on Jandy aquapure error code?
Salinity sensor sees less than .2 GPL of salt. Either there’s no salt in the pool or sensor is air locked. Flow salinity sensor temperature probe error codes. 1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3.
How to check salinity of Jandy aquapure pool?
Backwash filter if a DE filter is installed. Partially drain pool and dilute with fresh water until salinity returns to 3.0 to 3.5 gpl Unit wired to improper AC voltage. Contact a pool professional Verify proper flow/temperature/salinity sensor installation. Check salinity with Myron “L” meter calibrated for NaCl or test strips.
Why is there an error code on my Jandy chlorine generator?
It becomes especially difficult if the product, like the Jandy AquaPure Chlorine Generator, only displays an error code, but not necessarily what the error code means nor solutions to the problem. If you purchased the unit a year ago, it’s quite possible you may have misplaced or thrown out the manual. How will you diagnose the issue then?
1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3. How To Change a Jandy AquaPure Tri-Sensor Front board power supply is either too low or too high. 1. Generates code 173- Low input voltage, IF code 188 is present.
It becomes especially difficult if the product, like the Jandy AquaPure Chlorine Generator, only displays an error code, but not necessarily what the error code means nor solutions to the problem. If you purchased the unit a year ago, it’s quite possible you may have misplaced or thrown out the manual. How will you diagnose the issue then?
Salinity sensor sees less than .2 GPL of salt. Either there’s no salt in the pool or sensor is air locked. Flow salinity sensor temperature probe error codes. 1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3.
Which is salt water pool purifying system does Jandy use?
Jandy Pro Series AquaPure is a heavy-duty, electronic saltwater swimming pool purifying system that uses ordinary salt to produce chlorine for salt water swimming pools.