How do you replace a lawn genie valve?

Instructions

Shut off the Water. Shut off the water to the irrigation system by rotating the valve handle on the main supply pipe of the system.
Disconnect the Wiring.
Remove the Old Valve.
Prepare the New Valve.
Install the New Valve.
Connect the Wiring and Test.

Are Lawn Genie and Irritrol valves the same?

The DPR series are the same valves as the Lawn Genie model L701 & L703. The Irritrol APR model is a good choice for a residential system where a anti-siphon valve is appropriate (see below). These anti-siphon valves have a built in atmospheric backflow preventer.

Are sprinkler valve solenoids interchangeable?

It is also interchangeable with most brands of 24-volt automatic valves. This 24-Volt Solenoid replaces worn Orbit automatic valve solenoids. It is also interchangeable with most brands of 24-volt automatic valves.

How much does it cost to replace sprinkler valves?

Sprinkler Repair Costs Valve replacement averages about $12.50 to $40 per valve in addition to labor. Some heads can cost as much as $30 each, and brass valves range to $100 or more.

How do I turn on my lawn genie valve?

Manually open the valve by turning the bleed screw counterclockwise 1/2 turn. To close the valve, turn the bleed screw clockwise. Do not over-tighten!

How does Lawn Genie valve work?

The Lawn Genie L7034 Anti-Siphon Valve is equipped with a flow-control screw so you can easily adjust the rate the sprinklers emit water. The flow-control screw adjusts the amount of water pressure that goes to the sprinkler zone serviced by the valve.

Is Toro and Lawn Genie the same?

The company’s products are marketed under several brands: Toro – irrigation systems & supplies, professional and consumer mowers, compact utility equipment, snow blowers, and handheld trimmers and leaf blowers. Lawn-Boy – consumer mowers. Lawn Genie – consumer irrigation.

What causes a sprinkler valve to leak?

The most common reason leaks occur is that the rubber parts in the valve box have worn out. Water seeps freely through the system when the diaphragm seal breaks or debris is obstructing the valve from closing. A broken or aging sprinkler valve diaphragm seal only gets worse over time.

Do you need a Lawn Genie valve repair kit?

Additionally, the kit prevents homeowners from having to replace the entire valve. The kit contains parts for both angle and anti-siphon manual valves, along with stem assemblies and o-rings for both 3/4 in. and 1 in. valves and anti-siphon manual valves. The replacement parts are compatible with Models 706LG, 709LG, L3010, L3034, L4010, and L4034.

How does a Lawn Genie anti siphon valve work?

How do you change the flow control on a Lawn Genie?

Screw the solenoid into the new valve. Turn the flow control screw knob, the large screw knob on the top of the valve, clockwise until it stops to close the valve. Turn the water and power on. Turn the manual bleed screw, the smaller screw located to the side of the flow knob, counterclockwise to allow water through the valve.

What’s the replacement solenoid for a Lawn Genie?

The replacement solenoid for valve model 54003 is L10000 and the diaphragm is model 54006. The kit did not fit my application and does come with 2 valves and 2 o rings. I just ended up replacing the old with a different valve purchased at Home Depot. Good luck and not a difficult job.

Why do you need a Lawn Genie valve repair kit?

The kit’s replacement parts allow you to repair your valve rather than replace it. This saves you time and money. Additionally, the simple installation features will allow you to complete your valve maintenance quickly and easily. How can we improve our product information?

How do you replace a Lawn Genie sprinkler system?

If you have a Lawn Genie irrigation system, it is best to replace the valve with another Lawn Genie valve so the connector diameter and the distance between connectors will match up with your current system. Simply switch out the old valve for a new one. Turn off the water and power to the sprinkler system before attempting to replace the valve.

What’s the PSI of a Lawn Genie valve?

In-Line Jar-Top Valve Model L7010 is rated for applications from 10 psi to 150 psi. Thank you. Should water spray out from under the black valve when I open it manually?

What kind of diaphragm does Lawn Genie use?

Designed to help provide easy, do-it-yourself replacement for various Lawn Genie and RainJet valves, the In-Line Valve Diaphragm is made of reinforced materials. Compatible with RainJet valve models 204, 710A, 711A, 712A, RJ711 and RJ713. See Full Description Your store only has 0 in stock.