How tall is the Atwood g6a-7 water heater?

The only difference is this model has an automatic pilot whereas your old model had a manual pilot. Please note, if you wanted to use the Atwood RV Water Heater part # AT94180 (Gas Only, 10 Gallon, Manual Pilot), you’d need to ensure you have enough room for the new 16″ tall x 15-1/2″ wide x 20-7/8″ deep unit.

What’s the best replacement for an Atwood RV water heater?

The best replacement option we have for an Atwood G6A-7 Water Heater (Gas Only, 6 Gallon, Manual Pilot) is the Atwood RV Water Heater part # AT96121 (Gas Only, 6 Gallon, Auto Pilot). The only difference is this model has an automatic pilot whereas your old model had a manual pilot.

Is there a problem with my Atwood water heater?

This is actually a fairly common problem with older Atwood water heaters. Dinosaur has sold a lot of replacement boards for this very reason. A new board will fix the problem, but the board is not the problem. It is the connector on the wiring harness.

Is there a gas valve on an Atwood ignition?

If there’s no gas valve opening nor any HV arcing and the board is receiving full voltage, then I suspect the board.

Can a g6a-8e RV water heater be replaced?

RV Water Heater Thermal Cut Off Switch Kit Replace for Atwood 93866 Work for The Electronic Water Heater Models # GCH6-4E GCH6-6E G6A-7E G6A-8E GC6AA-9E GCH10A-2E G610-3E GH610-3E XT Series. In Stock. In Stock. In Stock. In Stock.

What kind of gas does an Atwood water heater use?

Atwood water heaters operate on L.P. gas or 110VAC. With the electric option, the heater can be run either off an electrical hook up or a generator. 98% of all serviceable components are accessed through the exterior door.

Why does my Atwood water heater not ignite?

There are several issues behind why your Atwood Rv water heater doesn’t ignite. In this chapter, we break down every possible cause and provide the solution as well. A thermocouple is a device that senses the heat of a pilot and lets the gas flow to the burner.

What kind of circuit board do I need for my Atwood water heater?

The quickest way to test a circuit board for your water heater is to use the circuit board from your Hydroflame furnace if you have one. The 8500 or 8900 models are the most compatible with your Atwood heater and should plug in easily. There will be the same 20-second delay that happens on your furnace when you power up the water heater.

Why does my Atwood water heater not light?

My Atwood g6a-8e water heater is refusing to light. The green light comes on on the control panel, but nothing happens – the red light doesn’t come on either. Last year I replaced the thermostats, the igniter and the pressure relief valve. The fuse looks good.

How many Atwood g6a-7’s are left in stock?

Only 1 left in stock – order soon. . Only 18 left in stock (more on the way). . Only 5 left in stock – order soon. . Only 2 left in stock – order soon.

What is the rating of the Atwood eco thermostat?

ECO Thermostat Assembly Replace for Atwood 91447 Replacement Part for Water H… 5.0 out of 5 stars. 4.0 out of 5 stars. 5.0 out of 5 stars.

How old is the Atwood mobile water heater?

The Atwood brand is 30 years old, and their designs are based on the older Bowen company which they purchased. Atwood has a great deal of experience building lightweight, reliable products for mobile conditions. Atwood water heaters slide in from the outside of the trailer and sit on the floor of the trailer.