Is there a problem with my Hayward pool pump?

Reliable & durable, Hayward pumps will still likely need some type of troubleshooting at some point during your relationship. Often what appears to be a pool pump problem is actually a filter problem or a valve problem, so the first step is to rule out any mis-aligned valves or obstructions in the filter or pipes.

What are the safety instructions for a Hayward pool?

READ AND FOLLOW ALL INSTRUCTIONS IN THIS OWNER’S MANUAL AND ON EQUIPMENT. KEEP SAFETY LABELS IN GOOD CONDITION AND REPLACE IF MISSING OR DAMAGED. WARNING– To reduce risk of injury, do not permit children to use or climb on this product. The ANSI/NSPI 4 Standard (above-ground and on-ground pools) advises that

Can a child climb on a Hayward pool?

KEEP SAFETY LABELS IN GOOD CONDITION AND REPLACE IF MISSING OR DAMAGED. WARNING– To reduce risk of injury, do not permit children to use or climb on this product. The ANSI/NSPI 4 Standard (above-ground and on-ground pools) advises that components such as the filtration system, pumps, and heaters be positioned to prevent their being

What kind of filtration system does Hayward pool use?

ISCC100 Rev. D OWNER’S MANUAL INSTALLATION, OPERATION, & PARTS XStream™Filtration Series The Hayward®XStream™ Filtration Series is specifically designed for the demanding requirements of today’s above-ground swimming pools. The advanced design reduces maintenance requirements while providing superior performance.

How big is a PVC water line collar?

It connects into the PVC water line with knurled threaded collar connecitons that are about 4″ to 4.5″ in diameter. Baciscally these collars screw on to threads on the other pipe. I assume that there must be a rubber gasket inside there.

How to remove the top of the Hayward chlorinator?

The suggestion to cut a piece of wood with a jigsaw seems pretty good. I imagine cutting two 2′ pieces at the center, using the same cutouts and slipping them on the lid and rotating would give you great leverage. Like someone said don’t crack your pipes or unions.

How to get PVC coupling out of pool?

Originally Posted by Coldjensens 1 Heat approximately 1.5″ of the screwdriver’s tip until red hot. 2 Press screwdriver into one side and out the other side of the valve. Try to get as close to the center of the valve as possible. 3 Pour water on the screwdriver and valve to cool and hardene any soft plastic.

What’s the best setting for the Hayward chlorinator?

I keep the chlorinator filled to the top with pucks and have tried 3.0 for a few weeks, which seem to keep the free Cl about 2-4 ppm and then suddenly one day it dropped to 0 ppm and I didn’t notice until an algae bloom had occurred. I’ve now got it on 4.0 setting and free Cl is up to 16 ppm, so I’m having a hard time finding a stable setting.

How big is the Hayward chlorinator pool pump?

My pool is 16’x32′ approx. 22,000 gal. and I’m running my pump 4 hr. in the morning and 4 hr. in the evening on 1,800 RPM.

Where do I get my water in Hayward CA?

PG&E will continue providing electricity to residents and business owners who choose to opt out of EBCE electric service. PG&E provides gas service to all Hayward accounts, both residential and commercial. PG&E can be contacted at 800.743.5000. Most properties in Hayward get water from the City of Hayward.

When do I get my Hayward water bill?

We do not complete account shut-offs on Fridays, weekends, the day before a holiday, or holidays. Also, you will receive a final bill within 1-2 weeks of your stop date. Account holder’s social security number and date of birth, or tax ID number (FEIN) for a business

Who is responsible for Hayward water and sewer?

The Revenue Division is responsible for administering the water and sewer billing for the Hayward Water System. The person responsible for the account can start or stop service. By phone: Call Customer Service at (510) 583-4600, Monday – Thursday, 8:00 a.m. to 6 p.m., and Friday, 8:00 a.m. to 12 p.m., excluding holidays.

What to do if your pool pump wont turn on?

If the motor does not turn on, check the breaker and timeclock switches. If the motor makes no noise at all, check the wiring and terminal connections. If the motor won’t come up to full speed, check the incoming voltage with a multi-meter.

Why does my pool pump have a spark at the end?

Sparking motors can be caused by loose wire connections or two wires or terminal connections touching each other, which is usually easily fixed. Sparking can also come directly from a short in the windings of the motor, which usually means the motor is near the end.

What should I do if my electric motor Humm does not start?

Check the belt tension between the motor pulley and the compressor unit. the belt should be firm, but not too tight. Check that the alignment between the motor pulley and the compressor pulley is straight and inline. The electrical circuit should be sized correctly to deliver the necessary starting amperage or inrush current.

What to do if your Hayward pool pump won’t turn on?

It’s a Hayward 3/4 HP Super Pump. With the power removed from the pump and the water valves off take out your leaf basket and see if you can reach into the impeller area and see if the impeller (pump vanes) is free/moving?

Why does my Hayward pool pump make a humming noise?

Makes Noise: If the pump motor makes a humming sound when trying to start, you likely have a bad start capacitor. On Hayward pumps, these are the black cylinder mounted at the rear of the motor.

What kind of voltage does a Hayward pool pump take?

If your Hayward pump runs for only 5 seconds and shuts off, check the incoming voltage. Most inground Hayward pumps are shipped to accept 230V, and if you only give it 115V, it can’t get up to speed.

Do you still need Hayward pumps and filters?

We carry the other brands, but Hayward pumps and filters have always been our flagship line. Reliable & durable, Hayward pumps will still likely need some type of troubleshooting at some point during your relationship.

What kind of valve does Hayward sand filter use?

Hayward offers a full line of multiport and slide backwash valves to support our complete line of vertical grid DE and sand filters. Utilized industry wide, Hayward backwash valves set the standard for performance and reliability.

What to do if your pool pump has lost Prime?

Check that the drain plugs are tightly inserted with Teflon tape, and that the pump basket is inserted in the proper way, and is sitting all the way down. If the pump has lost prime completely, fill a bucket with water or bring over a garden hose and re-prime the pump manually by filling up the pump.

Which is the best single element pool filter?

SwimClear single element cartridge filters are the industry’s most efficient and easiest to service single element cartridge filters providing best-in-class filtration performance and trouble-free service. StarClear Plus single element cartridge filters offer excellent quality, value and convenience.

How does the Hayward above ground pool filter work?

The Hayward ProSeries 18 In. Above-Ground Pool Filter System is designed to pair effortlessly with an above-ground pump to maximize filtration and deliver clearer water than ever before. It utilizes an umbrella-fold self-cleaning lateral system to provide efficient flow and evenly distributed water for long-lasting performance.

What do I need for a Hayward above ground pool pump?

Make sure this fits by entering your model number. INCLUDES: The Hayward ProSeries 18 In. Above-Ground Pool Filter System includes an 18 in. polymeric tank, a 7-position filter control valve, a 1 HP PowerFlo Matrix pool pump, a one-piece deluxe base and a 1 1⁄2″ hose package

Why is sand coming out of my Hayward pool filter?

If you see sand at the bottom of your pool, it could mean the sand is too small. No. 20 silica sand, .45 to .55 mm size, is required in a Hayward filter. Or, too much sand may be in the filter, causing it to flow into the pool. If you find dirt in the filter, it may indicate that the lateral sheets inside the filter are broken.

How often should I change the sand in my Hayward pool?

Hayward Sand Filter Repairs. Sand Change: Replace your filter sand every 5-7 years or sooner if your filter is undersized or if it has cleaned up a few algae blooms. Jackie wrote an entire “How To Change Pool Filter Sand” post about how to change pool filter sand, but here’s a 5-step summary. Drain the tank by removing the drain cap.

How to fix a Hayward pool cartridge filter?

Hayward Cartridge Filter Repairs 1 Remove clamp band and top filter half completely. 2 Remove belly band o-ring, and wipe clean with paper towel. 3 Replace tank o-ring and apply a thin layer of pool lube. 4 Replace lid and tighten up clamp band as tight as it will go. 5 If it still leaks, loosen clamp band, reposition it, and retighten.

Where is the air bleed screw on a Hayward pool filter?

Most new filters will have an auto air bleed that will bleed the air for you. If you are looking to bleed the air out of the Hayward EC style filters then you will find the air bleeder screw right by the discharge fitting. On other D.E. pool filters the air bleed screw is usually near the gauge on the pool filter.

How many connections are on a Hayward pool Control Board?

Control board has only 5 connections; ground, neutral, switched line (as in #2 above) and purple out to the gas valve, and the igniter cable. Gas valve rated at 120v, purple line should be supplying 120v or close.

Why is my Hayward h100id not getting ignition?

A few days ago, it showed the behavior identical to another thread. “Hayward H100ID Das Heater – Cycles Once, Then No Heat” but now I am not getting ignition even when the control board sees 120v and the igniter is firing. #2 if all conditions met, supply 120v to the control board until the thermostat opens.

When to turn off water heater in Hayward pool?

It turned the heater on 30 minutes after the circulation pump went on and turned the heater off 30 minutes before the circulation pump went off. This was to allow the water to cool down and not damage the plumbing lines. ALL Hayward heaters have Fire Tile, which dissipates the heat immediately, so a fireman’s switch is not required.

What should the salt level be in my Hayward pool?

Push the diagnostic button until “T-XX” appears on the display. Step 2: Verify the accuracy of the salt readings (2700-3400 pm) with an independent test kit or by taking a water sample to your local pool store for testing. 3200 ppm is the ideal level. If the salt level is below range, add enough salt to achieve a salt level of 3200 ppm.

Do you need fireman’s switch for Hayward pool?

This was to allow the water to cool down and not damage the plumbing lines. ALL Hayward heaters have Fire Tile, which dissipates the heat immediately, so a fireman’s switch is not required. NOTE: Gas fired heaters should be diagnosed and repaired by trained personnel.

What do you need to know about the Aqua logic?

The Aqua Logic is a multifunction pool controller used to fully manage your pool/spa system. The Aqua Logic can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Logic is easy to use, it is important to completely read through this operating manual before attempting to operate the control.

How many Hayward pump actuators does ProLogic control?

ProLogic: How It Works • All ProLogic systems are salt chlorination ready and can control 4-16 high voltage relays, 3-4 valve actuators and 1-2 heaters. • These systems can manage: Hayward Variable Speed Pumps, ColorLogic Lighting, Sense & Dispense, AquaConnect Homenet, as well as a wide variety of remotes.

Do you need a salt chlorine generator for Hayward pool?

Just like any other salt chlorine generator, the Aqua Rite may need a quick ‘tune up’ from time to time. Using information provided by Hayward Pool, we have created the following troubleshooting guide to help pool owners understand the diagnostic codes and quickly restore their Hayward Aqua Rite salt chlorination system. Important Tips!

How old does a pool pump have to be to fail?

The pump is typically more than 4 years old and is about to fail completely. The second is copper fatigue inside the windings. Again, the pump is usually more than 3 years old, and has been mounted on the sunny side of the yard, day in and day out, the electricity that flows through the copper windings heat up and the copper wire.

How to repair a Hayward Super II pool pump?

HowTo: Repair a Hayward Super II Pump – poolplaza.com – YouTube Taking a part a Hayward Super II Pump, and replacing the shaft seal. NEW Hours! Mon-Friday: 8am to 10pm, Sat: 9am to 3pm CST FREE SHIPPING Quick Contact: 1-8… Taking a part a Hayward Super II Pump, and replacing the shaft seal. NEW Hours!

Where is the hole in the Hayward pump?

So my Hayward Super II Pump is leaking from a hole near the motor end of the pump or where the motor mounts to #13 in the figure. Its hard to tell since its on the bottom.

Why is my Hayward Super pump suction leaking?

On the front of the super pump inside of the suction opening you will find a PVC fitting that is screwed into place. This fitting commonly leaks because the thread sealant or Teflon tape has worn off because the filter system has been disassembled and reassembled a few times.

Why does my Hayward pool pump blow bubbles?

If you have a Hayward Super Pump powering your above ground or in ground pool then you will know from time to time you may develop some air leaks inside of the pump. This air that gets sucked in from the pump fittings will travel through the swimming pool plumbing and then wind up blowing bubbles from the return jets of your pool.

How long does a pool pump usually last?

How long does a pool pump last? With regular use, most pool pumps last 8 to 12 years before needing replacement. That said, there are a few factors that affect how long a pump lasts. What affects a pool pump’s life expectancy?

How old is the pool pump in my yard?

Again, the pump is usually more than 3 years old, and has been mounted on the sunny side of the yard, day in and day out, the electricity that flows through the copper windings heat up and the copper wire. Inside the wire itself goes through a molecular change from the tremendous heat.

Why does my pool pump sound like a hyena?

But if your pool pump sounds a little like a screeching hyena, the issue could be bad bearings (which are mounted on the pool motor shaft inside the motor itself) inside the motor. For cavitation, the solution could be as simple as clearing a clog out of a plumbing line, or it could also be an air leak somewhere in your system.

What should I do if my pool pump is not primed?

If water is not flowing freely in the strainer box, return to step one and repeat. Switch the diverter valve back to half way between the skimmer and main drain. If the pump is still not primed, check the impeller for debris and filter pressure for anything 10psi above the clean reading for your pool filter.

Where does the pump go in a swimming pool?

Pool pumps are installed below the upper water level of the pool in pump pits or underground compartments. Water is gravity fed to the pump inlet when the pump is off. Once the pump is energized, the inlet line is under suction and the pump outlet, including the filter and return line to the pool, is under pressure.

How to fix a Hayward navigator pool vacuum?

1 The Hayward Navigator. A common pool cleaner is the Hayward Navigator, which consists of many moving parts. 2 Determining What Needs to Be Replaced. 3 Checking the “A-Frame”. 4 Disassembling the Navigator. 5 The Gearbox. 6 Final Step. 7 Questions & Answers. 8 Comments. …

Why is my Hayward Super pump not priming?

I have a hayward super pump II. It is not priming on its own. To get it to prime I must shut all 3 intake valves from my skimmers and the main drain, put water in the basket, turn on the pump and then 1/2 way open the closest skimmer. I must do this 3 times to get the thing to prime.

What are the flow requirements for a Hayward pool pump?

Current requirements: 6 FPS Suction side (coming from pool), 8 FPS Return side (returning to pool), per APSP-7. Desired Flow rate The flow rate between the minimum flow based on the Turnover rate and the maximum flow based on water velocity. It is recommended to select a flow that is higher than the minimum

Why is my Hayward pool VAC not moving?

If there’s not enough suction, it won’t move much. Question: My Hayward pool vac wasn’t moving so I replaced the A-frame and turbine kit. It now only stays in one section of the pool. No matter where I move it, it always makes it way back to the same section and does circles in that area.

Why does my Hayward pool pump keep leaking?

Leaks can also come from loose drain plugs or loose on bolts on the seal plate, connecting the motor to the pump. If the water is running down between the pump and motor, determine if it’s dripping out of the plumbing fitting on top or the shaft seal on the bottom.

How to fix a Hayward pool filter screw top?

To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: C_-5I0uKVpz5aA1L) An error occurred while retrieving sharing information. Please try again later.

What to do if your pool pump makes no noise?

If the motor makes no noise at all, check the wiring and terminal connections. If the motor won’t come up to full speed, check the incoming voltage with a multi-meter. If the motor is sparking and smoking, check the terminal wiring diagram for 230V. If the motor is loud, remove from pump and test briefly. If still loud, replace bearings/seal.

How to repair a common Hayward pool filter?

1 Remove the nuts and bolts around the top and bump handle pins. 2 Remove filter lid, then lift out the entire nest assembly. 3 Slide off the tube sheet top, and pull up the damaged flex tubes. 4 Push the new fingers in place snugly, replace tube sheet top. 5 With nest assembly in place, secure the filter top and bump handle. More

Why does my Hayward pool have too much water?

Or it may be time to replace the cartridge filter. If you can see dirt on the bottom of the filter element, then the pump is forcing too much water through it. When the water volume is too high, the filter is unable to catch all the contaminants. If you notice this symptom, the size of the pump or the amount of flow needs to be reduced.

What kind of sand do you need for a Hayward pool filter?

No. 20 silica sand, .45 to .55 mm size, is required in a Hayward filter. Or, too much sand may be in the filter, causing it to flow into the pool. If you find dirt in the filter, it may indicate that the lateral sheets inside the filter are broken.

What to do if Hayward pool filter leaks?

This is a common occurrence with Hayward filters. The whole point of HAVING a union is so you can detach the filter from plumbing and do whatever work needs to be done to pool equipment. If you loosen bulkhead and re-tighten you have a 50/50 chance of it leaking. The only fix is to buy a bulkhead union fitting kit : ( Loading…

Is there a Hayward Super pump seal kit?

ZFZMZ Replacement Hayward Super Pump Seal Kit 3. All 3 Gaskets & Shaft Seal. Fits All SP1600, SP2600 in Regular, X, VSP Models. SPX1600TRA SP1600Z2 PS-201 SPX1600R SPX1600S SPX1600T . Only 1 left in stock – order soon.

How big is the inlet on a Hayward Super pump?

There are two fitting connections on the Hayward Super Pump housing. These inlets can be either 1.5″ inches or 2″ inches depending on the horsepower and size of your super pump. You will need to connect both side of the pump to your swimming pool system.

What kind of sand filter does Hayward have?

Ihave a hayward 210t sand filter and I just replaced the sand in it. I followed the instructions and everything went well. except there was a leak from the gasket but I fixed that.

How to repair multiport valve on Hayward pool?

Hayward Multiport Valve Repairs 1 Remove 6 screws around valve lid and pull out key assembly. 2 Use small flathead screwdriver to remove all of the old gasket. 3 Place small dabs of super glue or silicone in the grooves. 4 Press in new gasket, wipe off any excess silicone. 5 Reassemble by replacing key assembly in the proper orientation.

How does a Hayward in ground pump work?

Hayward in-ground pumps are self-priming centrifugal pumps. These pumps have a vacuum chamber, commonly known as a pump housing. The pump housing must be filled with water in order to create a vacuum, resulting in the pump drawing the water out of your pool or spa.

How can I winterize my Hayward pool pump?

To winterize a Hayward Pool pump, turn off the electrical circuit breaker that supplies power to the pump. Also, make sure that there is NO water left inside the pump. All Hayward pumps are equipped with drain plugs that will allow excess water to drain once the plugs are removed.

Where is the impeller located on a Hayward pool pump?

The motor spins the pump impeller, located inside the pump volute. While the motor is rotating, the tips of the impeller are hydraulically sealed inside the pump diffuser, which is responsible for self-priming. Self-priming can only occur if the pump has a diffuser–all in ground Hayward pumps have an internal diffuser.

Which is the best Hayward pool pump EY?

This pool pump ey integrates seamlessly with most brands and can control virtually every kind of pool and spa equipment. Hayward’s best-selling Super Pump just got even better. Super Pump VS variable-speed pool pumps are a drop-in upgrade that deliver up to 80% energy cost savings over single-speed models.

What to do if your Hayward pool pump goes bad?

Check capacitor for …capacitance or resistance with an Ohm meter. If breaker still trips, replace the breaker; they go bad eventually. If your Hayward pump runs for only 5 seconds and shuts off, check the incoming voltage. Most inground Hayward pumps are shipped to accept 230V, and if you only give it 115V, it can’t get up to speed.

Which is the best variable speed pool pump?

VS Omni variable-speed pool pumps are the easiest, most affordable way to add smart control to existing pools and spas. This pool pump ey integrates seamlessly with most brands and can control virtually every kind of pool and spa equipment. Hayward’s best-selling Super Pump just got even better.

Why do you need a circulation valve in your pool?

Circulation of water is one of the most important parts of pool maintenance, water sanitation, and for keeping your pool looking and feeling its best. The best place to dive into pool circulation is with pool valves, which manage the movement of water in your pool.

How does the return system in a pool work?

Returns usually have an adjustable “eye” that lets you direct the flow of the water. It is best to direct the water in a consistent direction to “spin” the water around the pool. For instance, pointing all the returns in a clockwise direction helps the water circulate clockwise.

What are the parts of the pool circulation system?

The main parts of your pool water circulation system, more or less in order of the flow of water, are: 1 Skimmers 2 Main Drain 3 Pump 4 Filter 5 Heater (if you have one) 6 Chemical Feeder (not always present) 7 Returns More …

How does the Hayward pool circulation system work?

WARNINGCOMPONENT SEPARATION HAZARD Pool and spa water circulation systems operate under hazardous pressure during start up, normal operation, and possibly after pump shut off. Pressure in system can cause explosive component

Where can I find a Hayward pool manual?

ATTENTION INSTALLER: THIS MANUAL CONTAINS IMPORTANT INFORMATION ON THE OPERATION, AND SAFE USE OF THIS EQUIPMENT. THIS MANUAL IS INTENDED FOR THE END USER OF THIS PRODUCT Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207 Phone: (908) 351.5400 www.haywardnet.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

What’s the maximum working pressure on a Hayward pool?

C4030 425 39.5 150 568 C5030 525 48.8 150 568 C7030 680 63.2 150 568 MAXIMUM WORKING PRESSURE FOR ALL MODELS 50 PSI (3.45 BAR) ATTENTION INSTALLER: THIS MANUAL CONTAINS IMPORTANT INFORMATION ON THE OPERATION, AND SAFE USE OF THIS EQUIPMENT. THIS MANUAL IS INTENDED FOR THE END USER OF THIS PRODUCT Hayward Pool Products

Which is the best filter for Hayward pool?

Models C2030 C3030 C4030 C5030 C7030 TOP MANIFOLD CARTRIDGE FILTERS MODEL EFFECTIVE FILTRATION RATE DESIGN FLOW RATE Residential Commercial FT2M2 GPM LPM C2030 225 20.9 84 318 C3030 325 30.2 122 462

The hedgehog was engaged in a fight with

Is there a problem with my Hayward pool pump?