Is there an error code on my hot tub?
Is there an error code on my hot tub?
Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa’s equipment area.
What does hi limit mean on a hot tub?
Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump.
What does LF mean on a hot tub keypad?
LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours). Heater is shut down, but other spa functions run normally. dr = Inadequate water detected in heater. dry = Inadequate water detected in heater.
What does PSoC stand for in a hot tub?
PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable. Contact ACC. OHH = Overheat. Spa has shut down.
What does the code OH mean on a hot tub?
OH : Overheat. Spa temp over 108°. HLoH : Hi Limit Over Heat. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F. SEoP : Sensor open or disconnected. Heater disabled but spa operational. SESH : Sensor short, nonfunctional. Heater disabled but spa operational.
Where can I get a discount on a hot tub?
Browse a huge selection of Hot Tubs & Spas and many Spa Accessories available from reputable brands such as Dr. Wellness, Hudson Bay, and Plug & Power available at affordable prices from Aqua Living Factory Outlets.
What to do if your hot tub has an error code?
In some instances it may be more prudent to contact a local hot tub service company to assess and repair the spa pack as some diagnose procedures require special equipment. Please note that the Balboa Error Codes cover all circuit board manufactured by Balboa including Cal Spa, Marquis Spa, Master Spa and many others.
Is the cost of a hot tub covered by health insurance?
Many of our customers ask if hot tubs and spas are covered by health insurance. The answer is: it depends on your insurance company and your specific health plan. Your health insurance policy may cover the purchase price of a new spa if hot tub therapy has been prescribed by your doctor to treat a legitimate medical condition.
Is there a checklist for a hot tub?
Watch out: No single hot tub or spa inspection checklist is likely to be complete; the electrical system, water chemistry, tub access, slip and fall hazards and other conditions found at any hot tub or spa can include health, safety, and even fatal hazards.
Do you need access control for a hot tub?
Hot tub access control: adult supervision is required; children in this private home could easily access and enter the hot tub. No ground-fault interruption circuit (GFCI) has been provided for the hot tub electrics.
What are the electrical requirements for a hot tub?
All electrical work should comply with BS 7671. There are no specific requirements for electrical installations associated with hot tubs in BS 7671.
Do you have to have a NEC code for a hot tub?
The NEC code states that the disconnect must be within sight of the hot tub or spa. Additionally, all the equipment that is associated with the hot tub or spa must be protected by GFI, as your inspector will be sure to point out. Electrical Circuit Wiring for a Hot Tub Circuit: The electrical circuit is a dedicated GFCI protected circuit.
When to call in a hot tub repair service?
Spa repair services are specially trained in maintaining and fixing hot tubs (although they can sometimes work on pools as well). So when you’ve got a malfunctioning spa, it’s time to call in these experts. Reasons you may need to call in a hot tub repair service near you include:
When to use the spa and hot tub light?
The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. SESH = Sensor short, nonfunctional.
What does the topside Control Panel on a hot tub do?
And that’s all the topside control is – a control panel, think of it as a remote control for your hot tub, wired into your spa controller, which is really the brains of the spa system. The spaside control panel, it’s just a convenient way to turn things on and off, and view equipment status lights and water temperature.
How to know if your hot tub is overheating?
Hot Tub Topside Keypad Error Codes & Messages 1 Balboa. OH = Sensors reading 112-118° F. OHH = Overheat. Spa has shut down. One sensor has detected 118° F at heater. 2 Brett Aqualine 3 CTI. OH = Overheating, water over 112° F. System will restart when temp. drops. HL = High limit switch tripped. 4 EasyPak 5 Gecko 6 Hercules 7 Hurricane 8 Hydro-Quip
What to do if your hot tub does not heat?
To do this, consult the manufacturer’s guide or find it online. There are some simple things you could try if the hot tub does not heat the water. First of all, open and close the spa door on the spa cabinet, and see if it starts heating. If the hot tub is gas-powered, you should check if the pilot light turned off and turn it back on.
And that’s all the topside control is – a control panel, think of it as a remote control for your hot tub, wired into your spa controller, which is really the brains of the spa system. The spaside control panel, it’s just a convenient way to turn things on and off, and view equipment status lights and water temperature.
When do you get error code on your hot tub?
Updated on: December 23, 2020. Posted on: March 29, 2018. You likely look forward to a hot tub soak every day. So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret!
What do you need to know about hot tub bearings?
You will need to order the exact bearings for your model by contacting your Balboa retailer. Empty the hot tub of water before starting the troubleshooting process. If you cannot correct problems with these steps, contact an electrician to avoid damaging your hot tub.
What does it mean when spa goes into priming mode?
Pr = When spa is first actuated, it will go into Priming Mode. ILOC = Interlock failure – possible pump or ozone spike . (—) =Unknown water temperature. (Displays when first powered up after refill).
Why are the red and green lights blinking on my spa?
If both red and green lights are blinking, this could indicate low water flow. Resetting the spa by turning off the power, waiting and turning it back on is likely to resolve the issue. If these troubleshooting tips don’t solve your problem, consult the owner’s manual for your controller. You can also contact the manufacturer for technical help.
What does Th1 / 39 Mean on a hot tub keypad?
th1/39 = On startup indicates temperature probe problem. th2/current temperature = On startup indicates temperature probe problem. OH = Overheating, water over 112° F. System will restart when temp. drops. hot = Overheating, water over 112° F. System will restart when temp. drops. HL = High limit switch tripped.
What is the owner’s manual for a legend hot tub?
Inside the Legend Series Owner’s Manual, you’ll find valuable information on installation, maintenance, safety and of course tips for getting the most out of the long list of exceptional features that make Legend Series hot tubs, well, legendary.
What to do if your Master Spa code is not listed?
Below is a list of Master Spa error codes. The code on Master Spa is normally an easy fix, however, if your Master Spa code is not listed, please call customer care 855-308-2149; we do offer limited technical support. No message on display. Power has been cut off to the spa. Check your breaker and turn back on, if off.
What are the parts of a Master Spa?
Our Master Spa Legend Series hot tubs are ultra-premium hot tub spas, which look and feel luxurious with high-end parts such as Master Spa Legend Series control panels and high-performance Master Spa Legend Series filters.
How often does a Master Spa hot tub filter?
Your hot tub is only scheduled for filter 2 times a day for 2 hours. This may cause your water temp to not be at what you have it set at. The hot tub is in Sleep mode. While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. Your hot tub does NOT heat during this time in this mode. The hot tub is in Standby mode.
Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa’s equipment area.
What are the most common water heater code violations?
Code expert Glenn Mathewson describes 10 common water-heater code issues, including confusion about drip pans and drains, unsupported expansion tanks and plastic vents, lack of combustion air, and more. Some of these violations can be life-safety hazards, so avoiding these mistakes is crucial.
What does it mean when your hot tub is out of danger zone?
A freeze condition has been detected by the system. The jet pumps operates until the water is warmed and spa is out of danger zone. No action is needed. Note that this message may occur when the hot tub is filled for the first time because tap water is usually very cold. Indicates a hot tub power failure.
What to do if your Master Spa has an error code?
Unplug sensor and switch sensors around. If the problem switches to SnB, then you have a bad sensor. If the problem stays SnA, then you have a bad PC board. Same with the error SnB. Find replacement PC board. Sensors are out of balance. If this alternating with the temp, it may just be a temporary condition.