Info

The hedgehog was engaged in a fight with

Read More
Miscellaneous

Why did my Jandy LXI heater shut down?

Why did my Jandy LXI heater shut down? Jandi LXi400. Heater fires up 3 times for about 15 sec each and then shuts down with FAULT- CHECK IGN CONTROL error. The burner does light, I can see the flames and feel the blower and the heat. Is there a check IGN control fault on Jandy LXI? I'm getting a CHECK IGN CONTROL fault on my Jandy LXi. It will turn on and attempt to ignite a few times in 4 minutes, but it's unable to start. Step 15 - I do not know how to check if the igniter is...
Tips

How do you fix the SL code on a hot tub?

How do you fix the SL code on a hot tub? On them you need to press the 'TEMP' button and then the 'LIGHT' button within three seconds of each other and this will change the modes from EC (economy mode), to SL (sleep mode) and finally to ST (standard mode) which is what you want. What to do if your hot tub has an error code? Run a hot tub temporarily with filters out of the hot tub and see if the problem continues. If error message goes away you have dirty filters. If the problem continues make sure...
Tips

Why does my pool heater not heat correctly?

Why does my pool heater not heat correctly? POOL HEATER DOES NOT HEAT CORRECTLY REASON HEATING TIME IS TOO LONG SOLUTIONSCheck the LED light on the pool heater is working. Always use a pool cover REASON FILTER PUMP OR SAND PUMP DOES NOT MATCH THE HEATER SOLUTIONSReplace the filter pump/ Sand filter following the manual. REASON POOL HEATER SET-UP FAILED Do you need an electric pool heater for a small pool? Electric heater use the Joule effect to heat your pool so that you can use it all year round even if space is limited. Our heaters use the most...
Guidelines

Does vacuuming pool get rid of algae?

Does vacuuming pool get rid of algae? With this “vacuuming to waste” method, the algae is vacuumed up, goes through the pipes and pump, and is then sent out of the pool system, bypassing the filter. This not only protects the filter from clogging, but also ensures algae won't be reintroduced to the pool. How long after algaecide can you vacuum? 1) Brush and then perform a heavy shock on your pool. 2) Add an appropriate algaecide to the water while letting the pool equipment run continuously. And 3) vacuum your pool within 36-48 hours. Will Shock get rid of...
Trending

How do I reset my high limit hot tub?

How do I reset my high limit hot tub? The hot tub high limit switch is sometimes triggered when you're refilling your hot tub and can be reset by pressing the large red button on your spa pack. How do I clear the HL code on my Arctic spa? Spa display is reading HLTurn the power off at the breaker for 15 seconds and then flip it back on. This will reset the HL reading.You will notice the display show some numbers. If you see the HL come back within a day or so, this means that there is likely...
Q&A

Can I use a shower drain as a sink drain?

Can I use a shower drain as a sink drain? 1. Yes, you can vent the sink drain into the shower drain. 2. Usually, they can share the same vent if the vent is within 5 feet of both fixtures. Can you put a shower where a toilet was? If you are remodeling your bathroom and find that the shower will be installed over the location of the previous toilet, you can simply change the toilet drain to a shower drain. Can a vanity sink drain into a shower drain? I'm in the process of remodeling a basement bathroom. It...
Trending

Can you adjust water pressure valve?

Can you adjust water pressure valve? The adjustment screw raises and lowers the water pressure, but before it can be adjusted, you need to loosen the lock nut below it. Loosen the lock nut by half a turn with the crescent wrench. Turn the adjustment screw counterclockwise to lower or clockwise to raise the pressure. How to adjust a water pressure reducing valve? Using pliers or a wrench you can loosen the nut so that you can adjust it easily. Now that the screw is loosened you can either turn it clockwise to increase the water pressure or counterclockwise to...
Q&A

What problems can hard water have on a plumbing system?

What problems can hard water have on a plumbing system? Unfortunately, hard water can leave scaly deposits on plumbing fixtures and in pipes, and these can build up over time, causing clogs and corrosion to occur. What are the two main problems with hard water in plumbing system? The two minerals that most often cause hard water problems are magnesium and calcium. Does hard water cause plumbing scale? How Does Hard Water Damage Pipes? Hard water is not kind to your plumbing system. Repeated exposure to hard water will cause limescale to build up, eventually clogging the drains and decreasing...
Q&A

How many gallons of water does a humidifier use?

How many gallons of water does a humidifier use? Depending on the model you choose and the size of your home, a humidifier uses from 1.5 to 12 gallons per day when the furnace is operating. This minimal amount of water is enough to raise the humidity to your desired level, but not enough for you to notice a difference on your water bill. Should humidifier be connected to hot water? When the humidifier is wired to operate on a heat or HVAC fan call, hot water is required as it is the only heat source for the evaporation process...
Q&A

What hot water temperature is required for hand washing?

What hot water temperature is required for hand washing? 100˚F Water temperature for handwashing should be at least 100˚F (38˚C). Can you put your hand in 60 degree water? The industry standard is 60 °C or 140 °F, which will not generally cause damage if held in contact for 5 seconds. This is therefore the maximum temperature of any pipe or other surface which might be accidentally touched. Is water temperature important for hand washing? Other hand-washing factors are comparatively less important. When deciding between using hot or cold water, “the short answer is, water temperature doesn't matter,” says Schaffner....