What causes a schwintek slide to not move?

If the motors are out of sync, the slide may not move at all. Othertimes just one side may move, which will cause a bind in the gears and not allow it to retract or extend all of the way. Other issues with the slide could be a faulty part, such as a burned-out motor or faulty wiring.

What happens if a slide out is stuck in an RV?

If the slide out is stuck in, many times an RV can become almost unlivable. This is particularly true if the slide out encroaches upon the function of other amenities or blocks entryways, especially if it blocks a room that someone is already inside of.

What happens when your slide out won’t slide out?

A stubborn slide-out, though, can turn your trip in to a disaster. Either you spend your days climbing over furniture in an attempt to live in an RV with the walls pushed in or you can’t depart for home with a slide-out that refuses to retract for road travel.

Why does my car slide not retract all the way?

Othertimes just one side may move, which will cause a bind in the gears and not allow it to retract or extend all of the way. Other issues with the slide could be a faulty part, such as a burned-out motor or faulty wiring.

Why does my slide not retract after new motor?

After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.

Is there an electrical problem with the slide out?

Finding an apparent electrical button, the control panel was removed and the wires for the stuck slide were placed on another slide “in/out” button. Again, there was no power to the stuck slide when the “In” was pushed. The two young mobile repair techs were now perplexed and did not have the skill to trouble-shoot the electrical issue.

Why is my slide out not working on my car?

To get back home to Katy, the power supply wires to the motor were “reversed” so the slide could be retracted so I could drive home to Katy, TX. With the power supply wires “reversed”, the slide will now not extend.

How many amps does a schwintek inwall slide need?

Pull the motor up until disengaged, about ½” Bend back wipe seal and visually locate motor Locate and remove motor retention screw located near top of each vertical column. Trouble shooting flow chart Checking Fuses The Schwintek Inwall Slide requires a minimum of 30 amp fuse.

Where is the motor retention screw on schwintek inwall slide?

Mode Button Motor Retention Screw 1/2” Pull the motor up until disengaged, about ½” Bend back wipe seal and visually locate motor Locate and remove motor retention screw located near top of each vertical column. Trouble shooting flow chart Checking Fuses The Schwintek Inwall Slide requires a minimum of 30 amp fuse.

What does the red LED on a schwintek slide mean?

During operation when an error occurs the board will use the LEDs to indicate where the problem exists. For motor-specific faults the green LED will blink 1 time for motor 1, and 2 times for motor 2. The red LED will blink from 2 to 9 times depending on the error code.

What’s the override mode on a schwintek slide out?

Press the “mode button” six times quickly. Press and hold a seventh time for approximately five seconds (Fig. 3). 3. The red and green LED lights will begin to flash, confirming the override mode. 4. Release mode button. 5. Use the normal slide-out control switch to retract the room.

How to make a slide room in a schwintek?

1. Extend the slide room until about ¼ of the room is left inside the unit. 2. Jack up one side of the slide room just enough to hold its weight (Fig. 1). 3. Place the 2×4 block on top of the slide room (standing on its edge between the T-Molding and side of the unit. 4.

When to retime schwintek in wall slide out?

This happens when the two sides are not matching up when fully retracted or fully extended. Here are very simple instructions on how to retime your RV’s Schwintek In-Wall® Slide-Out if that occurs, as well as how you can prevent it from happening again in the future.

How does a schwintek controller keep in sync?

The Schwintek system has two motors that counts revolutions. This is what keeps the system in sync, or parallel. When the system is not fully extended or fully retracted each and every time, the controller loses its zero point. When we run the system in and out three times, it allows that controller to find the zero point.

How to troubleshoot schwintek in wall slideout system?

1. Bend back wipe seal. Visually locate motor and motor retention screw. Remove the screw (Figs. 4, 5 and 7). 2. Pull the motor up until disengaged. Replace the motor retention screw to hold the motor in this position (Fig. 6). 3. Repeat this process for both sides of the slide room. 4.

Why is my schwintek system out of time?

What we have here is a Schwintek system that is out of time. The way you know it’s out of time is because this side is fully extended, as opposed to this side which is still approximately four inches from full extension. The way to retime the Schwintek system is simple.

How long does it take to retim a schwintek slide out?

When you extend or retract the system, at the end of the stroke, you want to stay on the switch for approximately three to five seconds to assure that the controller is able to recognize the zero point. If you’d like more information about your Schwintek In-Wall Slide-Out-System, contact Lippert.