What does Unconfigured bad mean?
What does Unconfigured bad mean?
Answer. If ‘MaintainPDFailHistory’ is enabled (the default), then it is possible for all of the drives in a Virtual Drive (VD) to show up as ‘Unconfigured Bad’. At this point the Virtual Drive will not be accessible in the operating system, even though the data may be intact.
What does unconfigured good mean?
▪ Unconfigured Good – A disk is accessible to the RAID controller but is not configured. as part of a virtual disk. For example, a new drive inserted into a system.
What is LSI MegaRAID?
LSI MegaRAID SafeStore software, together with self-encrypting drives (SEDs), secures a drive’s data from unauthorized access or modification resulting from theft, loss or repurposing of drives.
How do I check my LSI?
Answer
- Install “storcli” on your ESXi hosts. For example: # esxcli software vib install -v=/tmp/vmware-esx-storcli-1.19.04.vib –no-sig-check.
- Identify the current Virtual disk configuration using this command: ( /opt/lsi/storcli/storcli /c0/vall show )
How do you use MegaCLI?
MegaCLI is a tool used as a command-line interface to communicate with the LSI family of RAID controllers. It manages and reports on MegaRAID SAS cards….Install and Set Up MegaCLI
- Step 1: Verify Your Hardware RAID Controller.
- Step 2: Download MegaCLI.
- Step 3: Extract the MegaCLI Package.
- Step 4: Install MegaCLI.
How do you rebuild RAID 1 after failing?
Follow these steps to rebuild a RAID volume after replacing a failed hard drive from a redundant RAID volume (RAID 1, 5, 10):…
- Turn on the system.
- Click Start.
- Click All Programs.
- Click Intel.
- Click Intel® Rapid Storage Technology.
- Click Rebuild to another disk.
- Select the replacement hard drive and click Rebuild.
Is LSI part of Broadcom?
LSI Corporation was an American company based in San Jose, California which designed semiconductors and software that accelerate storage and networking in data centers, mobile networks and client computing….LSI Corporation.
| Trade name | LSI CORP |
|---|---|
| Parent | Broadcom Inc. |
| Website | www.lsi.com |
How do I boot into MegaRAID?
Knowledge Base
- Boot the system and look for the BIOS Boot menu screen hotkey and press it a few times. It is usually F8 or F11.
- At the MegaRAID BIOS, press control H.
- The BIOS will be ignored and the system will end POST with the BIOS boot menu.
- Select the MegaRAID controller.
What is an LSI keyword?
In terms of SEO (search engine optimization), LSI keywords are search terms related to the main keyword you are targeting. They help to support your content and add more context to make it easier for both users and search engines to know what your content is about.
What LSI words?
What is Meant by LSI Keywords? LSI (latent semantic indexing) keywords are terms and phrases that are similar or related to a webpage’s target keyword. Their purpose is to help search engines better understand the content of the page by adding context and connecting the copy to the target keyword.
How do I import or clear a foreign configuration in LSI?
You can use the LSI Storage Authority software to import the foreign configuration to the controller or clear the foreign configuration so that you can create a new configuration using these drives. Perform the following steps to import or clear foreign configurations. 1. Navigate to the Controller dashboard. 2.
What is the difference between the megacli and the MegaRAID Storage Manager?
The megacli tool is used for managing the controller via the command-line interface. (Note: The RPM installs this in /opt/MegaRAID/MegaCli/ ). The MegaRAID Storage Manager (MSM) tool is used for managing the controller via a graphical interface.
How do I check the status of the LSI RAID controller?
To read the status of the LSI RAID Controller, the LSI megacli command-line tool needs to be installed. This is already pre-installed in the Hetzner Rescue-System. You can get the status of the RAID by using the following command (show all logical devices on all controllers): megacli -LDInfo -Lall -Aall
How do I set up unconfigured (bad) hard drives?
If these are in Unconfigured (bad) status, you can set them up using: For “r1”, enter “r0” or “r5” correspondingly (HDDs on Enclosure 252, Port 0 and 1, WriteBack on, ReadCache on adaptive, Cache also enabled without BBU): After you have installed an additional drive, the desired volume is reconfigured accordingly.