What is the standard footprint of a toilet?

Standard toilet dimensions are typically between 28–30″ deep, roughly 20″ wide, between 27–32″ high, and have a rough-in between 10–14″. Now you can find the perfect toilet.

How much clearance does a toilet flange need?

Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.

What is the rough in for toilets?

12 inches
The standard rough-in is 12 inches, though you may encounter 10-inch and 14-inch rough-ins in older homes. You should find the rough-in measurement in the new toilet’s product information.

Are all toilets the same distance from the wall?

Keep in mind you need some space on the sides as well. Toilet Rough In Dimensions: A toilet’s rough-in measurement is the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.

How do I know if my toilet is 10 or 12?

Take the cover off of the toilet tank, and lay the toilet on its side to access the underside of the base. Measure from the back edge of the base to the center of the closet hole, or drain hole. Note if the measurement is 10 inches or 12 inches.

What is the standard size of a bathroom?

between 36-40 square feet
What is the average size bathroom? An average sized bathroom is anywhere between 36-40 square feet for an apartment or small home. This size is the general size as it encompasses both ¾ baths as well as full baths, giving you just about enough room for a shower, a bath, a sink and a toilet.

Should a toilet flange be flush with the floor?

The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.

How do I know if my toilet is a 10 or 12 rough?

To determine the size of your toilet rough-in, measure from the wall behind the toilet to the bolt caps of your current toilet. Most toilets are available in a 12-inch rough-in, which is the standard distance, but a 10- or 14-inch rough-in may be needed in some homes.

How much should it cost to have a toilet installed?

How Much Does it Cost to Install a Toilet? The typical toilet installation cost will run you between $122 and $228. Note that these prices do not factor in how much the toilet itself will cost. As a homeowner, you will be in charge of supplying it.

What is the minimum distance from toilet to wall?

15 inches
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

What’s the minimum clearance in front of a toilet?

The clearance in front of a toilet shall not be less than 21 inches to any wall, fixture or door when subject to the International Residential Code or not less than 24 inches when subject to the Uniform Plumbing Code. It is important to understand that these are minimum measurements. You can place the toilet further away.

How big should the space be in front of the toilet?

Minimum Clearance in Front of the Toilet 1 Code minimum: 21 inches from the front of the toilet 2 Recommended: 30 inches from the front of the toilet 3 Disabled access: 30 inches to 48 inches from the front of the toilet More …

How tall of a ceiling do you need for a toilet?

Minimum 21-inches clearance in front of toilet. Minimum 6-feet 8-inches of height to ceiling at the center of required area in front of toilet where there is a sloped ceiling over toilet. Also see our blog posts Why is there sand in the bottom of my toilet tank? and Why is there mold inside my toilet tank?

How to know the dimensions of your toilet?

Toilet Dimensions & Measurements to Know 1 In This Guide 2 Toilet Bowl Shapes. Elongated: Pear-shaped in design, this bowl option offers additional comfort and is typically two to three inches longer than a round bowl. 3 Seat Heights. Seat height is measured from the floor to the top of your toilet seat. 4 Standard Toilet Dimensions. …

How much clearance should a toilet have around it?

Clearances around toilets and water closets (WCs) can be measured from the face of the fixture or from its center line and are used to best service the toilet user. Minimum clearances between the face of the toilet fixture and the wall or nearest obstruction element are at least 24″ (61 cm)* but are recommended to be 36″ (91 cm).

What are the minimum clearances around a toilet?

Toilet Clearances. Clearances around toilets and water closets (WCs) can be measured from the face of the fixture or from its center line. Minimum clearances between the face of the toilet fixture and the wall or nearest obstruction element are at least 24” | 61 cm* but are recommended to be 36” | 91 cm.

What is clearance around a toilet?

Most codes require 15 to 18 inches of clearance at both sides of a toilet and at least 2 feet of clearance from the bowl’s front tip to the nearest wall or plumbing fixture.

What is the minimum space in front of a toilet?

To pass state building code, every fixture in the bathroom, including the toilet, must have a minimum of 21 inches of clear floor space in front of it. For many users, however, 21 inches is not enough; the recommended amount of floor space in front of a toilet is 30 inches.