When do you need to replace a vokera boiler?

Should the whole component need replacing, and your Vokera boiler was installed more than 10 years ago, you might want to consider a replacement Vokera boiler. Seeing the Vokera A03 error code, likely to be accompanied by the image of a bell, means that your boiler’s fan is faulty.

What does an error code mean on a vokera boiler?

When there’s a fault with your Vokera boiler, it will display either an error symbol or an error code, to help you decipher what these mean, use our list of Vokera error codes. Should You Replace Your Vokera Boiler Instead? An old boiler can end up costing you quite a bit in repairs so it can make sense to replace it with a brand new one.

What does fault code 40 / 41 on vokera mean?

However, if voltage IS going to the gas valve, it’s either the gas valve itself or the solenoid valve. 3. Vokera Linea fault code 40/41 (Vokera Compact code A04) The Fault: The codes above mean your boiler’s pressure levels are low. Sometimes this can happen if there’s a leak, or if an air bubble has found its way into the system.

Why is water dripping out of my vokera boiler?

It turned out the boiler now had electrical problems, caused when the connections had been disturbed when replacing the valve. This resulted in water dripping onto the PCB, making the electrics short out. The cost of replacing the PCB wasjust too expensive, and the boiler was then replaced.

What kind of boiler is a vokera mynute?

The Vokera 10, 14, and 20e Mynutes are central heating boilers, which – by design – incorporate electronic ignition, circulating pump, expansion vessel, safety valve, pressure gauge, and automatic by-pass. They are produced as room sealed, category II2H3+ appliances, suitable for wall mounting applications only.

Can a mynute range be used with a vokera twin flue?

The Mynute range can also be used with the Vokera twin flue system. These appliances are designed for use with sealed systems only; consequently they are not intended for use on open vented systems. The provision of stored hot water is possible by the addition of an indirect cylinder. A range rating facility is incorporated in the appliance.

When to turn off the burner on a vokera boiler?

Once your boiler reaches set CH temperature, the burner will stop for minimum 3 minutes and in the instances where temperature of central heating reached required level your boiler will turn off the burner automatically. Don’t forget that your appliance should be cleaned with a clean damp or soft cloth.

Why do I get a vokera A03 error code?

Seeing the Vokera A03 error code, likely to be accompanied by the image of a bell, means that your boiler’s fan is faulty. If you’ve had your boiler for some period of time then this suggests that it has worn down over time and needs replacing.

What does a code 10 on a vokera boiler mean?

Press the reset button and watch your boiler fire back to life. 2. Vokera Linea fault code 10 (Vokera Compact code A01) The Fault: The above codes mean that there is an ignition failure with your boiler, in which case you can probably hear your boiler sparking but failing to ignite.

How much does it cost to install a vokera boiler?

If you are getting a new Vokèra boiler installed into your home price is likely to be an important factor. The cost of installation is likely to be impacted by the model of the chosen boiler, its size and the overall complexity of the installation process.

How do you reset a vokera hot water boiler?

To reset your Vokera boiler, move the mode selector switch to the ‘OFF/RESET’ position and then move it back to either ‘hot water only’ or ‘heating and hot water’. Should this reboot get your boiler working again then you’ll know because there will be a constant green light.

What causes a vokera boiler to fail to ignite?

There are many reasons why a boiler might fail to ignite, from no gas supply to a faulty ignition lead or PDB board. You’ll need a Gas Safe engineer to diagnose and repair the A01 fault as you should never carry out any work on your gas boiler yourself. You can find a full list and explanation of all Vokera boiler fault codes on Boiler Guide.

What does A01 mean on a vokera boiler?

A common Vokera boiler fault code is A01 which means that the boiler has failed to ignite. There are many reasons why a boiler might fail to ignite, from no gas supply to a faulty ignition lead or PDB board. You’ll need a Gas Safe engineer to diagnose and repair the A01 fault as you should never carry out any work on your gas boiler yourself.

What does vokera Linea fault code 40 / 41 mean?

Vokera Linea fault code 40/41 (Vokera Compact code A04) The Fault: The codes above mean your boiler’s pressure levels are low. Sometimes this can happen if there’s a leak, or if an air bubble has found its way into the system. The Fix: Locate the filling loop underneath your boiler and top up the pressure to 1 – 1.5 bar.

What are the most common faults of a vokera boiler?

Luckily, there ARE some fixes you can try for Vokera boilers, which is why I’ve made life a little easier by listing 5 of the most common faults and fixes you can try at home, below. 1. Vokera Linea fault code 92/93 & 95 The Fault: These particular fault codes above indicate that your condensate pipe is either blocked, failing to drain, or frozen.

How does frost protection work on a vokera boiler?

Frost protection function will keep burner or/and pump operating until main water temperature reaches level of 35°C for central heating water and 55°C for hot water only. To sustain the frost protection function you need to provide your boiler with electrical supply at all times.

Where can I get technical support for vokera?

Vokèra’s technical support centre is available to offer advice over the phone for Gas Safe Registered engineers. Our support line is open Monday to Friday 8.15am to 5pm and Saturday 8am to 12pm. To contact us, please call: 0141 465 4545 or email: [email protected].