Info

The hedgehog was engaged in a fight with

Read More
Lifehacks

Where do you find the model number on a weed wacker?

Where do you find the model number on a weed wacker?

On homeowner trimmers, it is located on the bar code label on the fan casing. On professional units and brushcutters it is on the bar code label and stamped in the top of the cylinder or main crank case.

How much is a Featherlite weed eater?

According to some reviews, the mixture of oil and gas should be 1 to 50 since the one written in the instructions may not be able to start the Weedeater. All in all, the Weedeater Featherlite gas trimmers will give you what you expect for about 60 bucks.

How often should you change the spark plug in a weed eater?

approximately every 100 hours
As a general rule, you should change the spark plug approximately every 100 hours.

What is the lightest weight weed eater?

Makita XRU02Z 18V LXT Lithium-Ion Cordless String Trimmer. Without a doubt, the Makita XRU02Z 18V LXT is the overall highest performing, as well as one of the lightest weed eaters on the market.

Do manual edgers work well?

Lawn edging is a physically intensive task. You can use powered lawn edger, but those are expensive and need more care. But if you have a small yard and need some occasional edging work, then manual lawn edger is the best choice.

Are weed Wackers and trimmers the same?

A string trimmer, also called a weed eater, weed whacker, weedwacker, weed whip, line trimmer, brush cutter, whipper snipper (in Australia, Canada, and South Africa) or strimmer (in the UK and Ireland), is a garden tool for cutting grass, small weeds, and groundcover.

What is the lightest weight Weed Eater?

Where to find the fl20 Weed Eater instruction manual?

WEED EATER 1030 Stevens Creek Road Augusta, GA 30907 Trademark Instruction Manual FL20 WEED EATER 6150 McLaughlin Road Mississauga, Ontario L5R 4C2 545137258 11/30/06… Page 2 SAFETY INFORMATION MANUAL ON THE UNIT DANGER: Never use blades or flailing devices.

What should I do with my Weedeater Featherlite?

– Make sure unit is assembled correctly as shown in this manual. – Make carburetor adjustments with lower end supported to prevent line from contacting any object. – Keep others away when making carburetor adjustments. – Use only recommended WEED EATER accessories and replacement parts. – Mix and pour fuel outdoors.

What should fuel ratio be on Weed Eater Featherlite?

(A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules under FUEL SAFETY. Push and hold engine stop switch in the STOP or OFF position until the Weed Eater unit has fully stopped. Need Parts?

What kind of Weed Eater is called Featherlite?

Weed Eater, a famous string trimmer company offers variety of accessories for cutting the lawn. There is a special series of trimmer products specifically named “Featherlite”, referring to a lightweight and inexpensive device.

What’s the difference between a weed eater and a fl20?

Some of the parts that are manufactured for this trimmer can be used on either Weed Eater, Poulan, Husqvarna or Jonsered. The difference between the FL20 Type 1 and 2 is the carburetor. Type 1 uses a Walbro carburetor and the Type 2 uses a Zama carburetor. Also type 1 and 2 have different parts within the shaft and head of the trimmer.

What kind of oil does a Featherlite Weed Eater use?

The FeatherLite trimmer is designed to run on a 40-to-1 mix of gas and oil. That is equal to 3.2 fluid ounces of two-cycle engine oil to 1 gallon of gasoline.

How long does it take to repair a Featherlite Weed Eater?

Trigger and trimmer spool on my weedeater were broken. I replaced the trigger (it was held on with 4 star screws) and I put the new line spool on. In less than 15 minutes and for 22 dollars I was able to repair my weedeater.

When did the Featherlite straight shaft Weedeater come out?

I’ve owned a featherlite straight shaft weedeater since 1999..bought it new and it still runs great. The only thing i’ve ever done to it was replace the string spool with one that you just stick two pieces of line through. Its much easier than wrapping the line and lasts longer.