Why does my hot spring Vanguard not heat?

I have a hot spring vanguard that will not heat. My heater relay board checks out ok, but on the main circuit board the lem light is lit but the heater led is not lit. On my control panel the red power light is lit, but after a few seconds of turning on the power the green ready light starts to flash.

Why is my hot springs spa not heating?

Why is my Hot Springs spa not heating? • Integrated pressure switch open – check for clogged filters. The integrated pressure switch will reset when the flow of water through the heater has been restored. Contact our customer service team for a service if the heater trips frequently.

Is there an error code on my hot spring?

So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret! Hot Spring ® spa systems are reliable and will last a long time with regular maintenance, but issues do sometimes arise.

Why is my hot spring spa blinking green?

Blinking ready (green) light is a temperature sensor reporting is it too hot. Low flow – This can be caused by a plugged filter or by a failing circulation pump – Best test is to turn the power off and remove filters completely, turn tub back on and see if the blinking light comes back.

How to see the depth of the vanguard hot tub?

Drag the hot tub left or right to see a detailed, 360-degree view of the spa seating, jet placement, spa shell and cabinet. Turn the spa to see the hot tub depth and look closely at the available jets. The Vanguard Jet System offers an incredible 38 jets that relieve-tension in targeted areas including your back, neck, shoulders and calves.

What does the vanguard hot tub jet system do?

The Vanguard Jet System offers an incredible 38 jets that relieve-tension in targeted areas including your back, neck, shoulders and calves. Hot Spring Spas revolutionized spa industry with this one-of-a-kind moving jet that cascades up and down your back. If playback doesn’t begin shortly, try restarting your device.

What does it mean when a hot spring shuts down?

Stands for “Overheat”- and the tub shuts down because water temp is too hot. Temperature is not safe. The circ. pump will stop functioning to reduce frictional heating when water temp reaches 2°F (1°C) more than the set temperature.

When to replace hot spring no fault 1500 heater?

Use this kit if you’re replacing your original No-Fault® 5500 or No Fault 1500 Cartridge Style heater on a 1995-1996 Hot Spring or Tiger River spa. Click the “More Info” button for details. This PDR (power down reset) Titanium Heater is the generic replacement heater for all 1995-now Hot Spring and Tiger River spa models.

Which is the newest hot springs hot springs heater?

73790 This 2015 No-Fault PDR (power down reset) Titanium Heater is the newest factory upgrade replacement heater from the makers of Hot Springs spas. Its double-pass sleek design replaces all previously discontinued heater styles.

What to do if your hot spring spa lights keep blinking?

Turn power to the spa off for 1 minute, then turn power back on. For 240 v spas, turn on the 20 amp breaker and then turn on the 30 amp breaker. For 120 v spas, plug in. If light continues to blink, Call our Spa Service Department for a service call. 413-594-2666 ext 110 My Hot Spring Spa has blinking Green and Red lights.

What should I do if my hot spring heater is not lit?

It is important that the red HTR ON light is lit before continuing. If it’s not then please contact us. Now turn off the power to your spa. Either unplug it if it’s 120 volt model or turn off the breakers if it’s wired 240 volts.

How do you turn off a hot spring heater relay board?

Now turn off the power to your spa. Either unplug it if it’s 120 volt model or turn off the breakers if it’s wired 240 volts. Find where the black and white wire from the heater’s power cord connect onto the front of the heater relay board.

Why does my hot spring have a blinking light?

Low flow – This can be caused by a plugged filter or by a failing circulation pump – Best test is to turn the power off and remove filters completely, turn tub back on and see if the blinking light comes back. If it does not, replace circulation pump filter (the one with the gray cap).