Why does my Lippert LCI leveling system not work?

My Lippert LCI leveling system is showing jacks down when the jacks are up. All the lights start blinking with break off and ignition on. Cannot lower jacks.

How to check LCI fluid level with dip stick?

All the lights start blinking with break off and ignition on. Cannot lower jacks. Reset by pushing all four buttons just stops it for a second then lights start blinking again. Checked fuses. After a few minutes just the lights on left side blink. Trans fluid level is hard to check as it is transparent on the dip stick.

Where is the Trans fluid level on the LCI?

Checked fuses. After a few minutes just the lights on left side blink. Trans fluid level is hard to check as it is transparent on the dip stick. But the see through fluid tank shows level is about an 1-1/4 in below top of tank. The upper dip stick notch is near this height.

What should I do about my 5th Wheel leveling system?

For instance, the Replacement Control Module for Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC304136 is the replacement for the Ground Control System. This sounds like it is a ground issue. If your ground wire from the control module is grounded to the frame, I would try removing the ground and cleaning the surface.

My Lippert LCI leveling system is showing jacks down when the jacks are up. All the lights start blinking with break off and ignition on. Cannot lower jacks.

What should I do if my leveling jacks are not working?

Silicones and cleaning agents such as Dawn dish soap can worsen the corrosion and render your system irreparable. So what you should do is spray the system well with WD-40 and then wipe clean.

Why is my Lippert ground control not working?

The back light comes on, but no words, It seems like everything else works, I can press the auto level button and it works. I can press the retract button and retract the landing jacks, I just cant see anything on the display. This is on my touchpad connected to the RV. Not a remote. Anything I can do? The good news is your system is working.

How big are the level UP JACKS on a 5th Wheel?

Level-Up® is an Automatic Leveling system. This system is equipped with 14K Aluminum Front Jacks with 21” of travel and 8K Aluminum Leveling Jacks with 15” of travel. The jacks in the Level-Up® system work in pairs.

How to troubleshoot LCI leveling system troubleshooting panel?

Troubleshooting Panel of LCI Leveling System that Has Down Light that Stays on All the Time Front Jack Legs On Lippert Ground Control Lower When Slide Is Used Setting Up Lippert Ground Control 3.0 After Installing Replacement Control Module

How can I Reset my Lippert LCI leveling system?

My Lippert LCI leveling system is showing jacks down when the jacks are up. All the lights start blinking with break off and ignition on. Cannot lower jacks. Reset by pushing all four buttons just stops it for a second then lights start blinking again. Checked fuses. After a few minutes just the lights on left side blink.

How does a ground control leveling system work?

In minutes, your camper is leveled and you have extra time to do…well, whatever you want! Available in both 4-point and 6-point configurations, the Ground Control 3.0 power leveling system uses Hall Effect technology to efficiently and accurately level your RV by measuring the motor revolutions of your jack’s legs, instead of amps.

What kind of fluid do you use for leveling jacks?

Hello Joe, Typically Fleetwood used the Power Gear leveling system which is now owned by Lippert Components Inc (LCI). According to the Power Gear manual, they recommend the following: Type A automatic transmission fluid (ATF, Dexron III, etc.,)will work satisfactorily.

How does Ground Control 3.0 Power leveling system work?

Available in both 4-point and 6-point configurations, the Ground Control 3.0 power leveling system uses Hall Effect technology to efficiently and accurately level your RV by measuring the motor revolutions of your jack’s legs, instead of amps.

What to do if your Lippert LCD is not working?

Before replacing the third one, I recommend unplugging the connections on the panel and cleaning them prior to reconnecting. If this doesn’t solve your problem, then I recommend the Replacement Auto Level Control Panel for Lippert Ground Control Leveling System # LC421484 to give you the working LCD display.

How to control the LCI leveling system in a RV?

Push the “REAR” button to extend the middle and rear landing gear legs. Push the “LEFT” button to extend the driver’s side middle and rear jack. When pressing this button the middle jack will extend first then the rear. Push the “RIGHT” button to extend the passenger’s side middle and rear jack.

Why is my Lippert ground control leveling not working?

I dont know if the leveling system is a 2.0 or 3.0. The display on the touch pad is blank. The back light comes on, but no words, It seems like everything else works, I can press the auto level button and it works. I can press the retract button and retract the landing jacks, I just cant see anything on the display.

How to manually control your LCI® leveling system?

Push the “UP” arrow once, or until the screen reads “MANUAL MODE”. Push the “ENTER” button once. Push the “FRONT” button to extend the front landing gear legs. Push the “REAR” button to extend the middle and rear landing gear legs. Push the “LEFT” button to extend the driver’s side middle and rear jack.

Which is the right button on the LCI?

The “FRONT” button controls both left and right front jacks. The “LEFT” button controls the middle jack and rear jack on the driver’s side. The “RIGHT” button controls the middle jack and rear jack on the passenger’s side.

Why are the leveling jacks on my RV not working?

We’ve had a handful of members write in wondering what to do when the leveling jacks on their RV’s slide room, fifth wheel or tow trailer aren’t working properly. For most of these cases, their hydraulic system has either taken on a disturbing growling noise upon descension of the leveling jacks or they simply won’t retract back into the rig.

How long does it take to reset a LCI controller?

It requires 5 seconds, but many people will count to 5 a little too fast and the system won’t reset. He said if that doesn’t work then the controller is bad and will need to be replaced.

What to do if your leveling jack wont extend?

To help you troubleshoot the situation and find the right solution, RVing expert Dave Solberg teaches you how to diagnose a faulty leveling jack system. You’ll learn what to do to safely inspect your fluid reservoir and valves, and discover the most common reason RV jacks won’t extend.

It requires 5 seconds, but many people will count to 5 a little too fast and the system won’t reset. He said if that doesn’t work then the controller is bad and will need to be replaced.