Why does my speedometer work but not my odometer?

If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced. These are easily installed and located near the back of your transmission. If only your odometer is busted, then it’s likely the gears that turn the odometer have broken.

Does broken speedometer affect odometer?

Speedometers and Odometers sometimes work in tandem but very often do not. It would depend on the specific model and options (possibly things such as stability control) on your vehicle but generally speaking most odometers will still track mileage even if the speedometer doesn’t work.

Why would my odometer stop working?

If both your odometer and speedometer are malfunctioning, then there may be an issue with your speed sensors. However, if only your odometer has stopped increasing, it may be an issue with the gears that drive it. As a result of the plastic gears that turn them, analog odometers have a high propensity to break.

Is odometer hard to fix?

When your odometer ceases to work, most people assume they must replace the unit, which can get quite expensive. However, you can repair an odometer fairly easily. The odometer stops working because the gear within the odometer has worn out.

Why does my speedometer get stuck?

The speed sensor on the passenger axle may need to be replaced, or the speedometer cable may be damaged or broken. If the needle is stuck, the fuse in the fuse box may be faulty. The speed sensor may also have gone bad. You will need to recalibrate the speedometer or get it replaced.

What does it mean when your speedometer stops working?

you need to verify everything else works on the gauge works. if your gauge reads miles built up, that means it is getting signals from speed sensor on how fast the unit is moving and how far. so that is telling us that your gauge is recieveing signal from sensor. Ask Your Own Motorcycle Question Customerreply replied 10 years ago

Why is the odometer on my car not working?

Initial guess was that the gear was broken, luckily it was a wrong guess. Disassembling the unit showed that the gear was just not rotating together with the axle, and hence the ODOMETER wouldn’t work. These meters cost hundreds of ringgit but they’re not difficult to fix. I’d repair these than to pay a fortune for a new one. Loading…

What’s the speedometer on a 1999 sportsman 500?

I have a 1999 Sportsman 500 ATV. When I ride, the speedo needle will go down while I maintain speed. It gets to about 5 mph, stays there for a few … read more Fully Licensed Motorcycle… I have a 99 sportsman 500 and the speedometer quit working and when that went so did the 4×4 switch and the kill switch. Will replacing the … read more

Is it time for a new speed sensor?

Perhaps it is time for a new speed sensor? or is it time for a new speedo. 2000 softail deuce. Okay. I replaced the speed sensor ($58) from the dealer.

Why does my odometer and speedometer stop working?

Your speedometer and odometer can start acting wonky (or stop working altogether) for two main reasons: either your vehicle’s speed sensor or speedometer gauge cluster have failed. Both problems are simple and inexpensive to fix, even for the novice DIY-er.

Can a broken speedometer lead to a ticket?

You should diagnose and resolve the problem as soon as you see it, since not knowing how fast you are going can lead to a ticket. Also, in most states you won’t be allowed to register a car with a broken speedometer. A faulty, damaged, or broken VSS can cause your speedometer to fluctuate and completely stop working.

How can I get my Honda odometer to work?

Use a Phillips screwdriver to remove the screws of the dashboard bezels. There is one near the A/C controls and another above the gauge cluster itself. Undo several clips on both sides of the dashboard bezel, and remove it. Use a 1/4” ratchet, socket and extension to remove the wiring cluster from the dashboard.

How do you replace a speedometer on a Honda?

Undo several clips on both sides of the dashboard bezel, and remove it. Use a 1/4” ratchet, socket and extension to remove the wiring cluster from the dashboard. Unplug the harness from the gauge cluster. Plug the stock harness into the replacement gauge cluster/speedometer. Use the 1/4” ratchet, socket and extension to install the new cluster.