Why is the circ pump on my Sunrise spa not working?

If the circ pump is not operating it could produce the FLO message. A locked up pump could also cause the GFCI breaker to trip. The pump motor could need a new start capacitor or the motor itself could be on the way out. If all else fails contact your local Spa Service Support Desk to book a Diagnostic and Repair of your Sunrise Spa.

When to replace a hot tub control panel?

If you have tested the control panel and it does not work with one you know is good, you will probably need to replace the circuit board. Some symptoms of a circuit board problem are a blank or partially blank display, slowness in displaying messages, or LED lights that are not working properly.

What kind of chemicals are in calspas owner’s manual?

WARNING: This product can expose you to chemicals including Chromium (hexavalaent compounds), which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.p65Warnings.ca.gov

Where can I find the Genesis spa manual?

Use Adobe Acrobat Reader DC to view all manuals. Note: The Genesis manuals listed below are for an acrylic spa sold from 2009-2011. For roto mold spa manuals, see the section further down on this page.

Where are the Cal spas hot tubs located?

Cal Spas was born. Cal Spas current headquarters grew into a 1-million square foot State-of-the-Art manufacturing plant in Pomona, California. When you bask in the warm waters of your new hot tub or swim spa, you are free to let your imagination wonder while the stresses of the day disappear. Cal Spas, too, was borne of pure imagination.

What are the features of a Cal spa?

Cal Spas Swim Spas X-Series combines our best models from the Swim Pro™ line and takes it to the next level of visual and ergonomic design with new features such as Elite™ cabinets, Cal Grip™, Cal Touch4 Control™ and Cal Armor™. Hot Tub Hydrotherapy is essential for many of you in your daily routines and rehabilitation.

Can you replace a spa with a hot tub?

“I replaced a spa and went with Cal Spas. Dealing with their customer service was pleasant and easy. I literally pulled up the freeway, walked-in and made a deal. The hot tub had to go in an existing hole in the ground, so Cal Spas connected me with a carpenter that came.

How many Cal spas swim pros are there?

We offer 6 different models in our Swim Pro™ line. Cal Spas Swim Spas X-Series combines our best models from the Swim Pro™ line and takes it to the next level of visual and ergonomic design with new features such as Elite™ cabinets, Cal Grip™, Cal Touch4 Control™ and Cal Armor™.

How to take care of your hot spring spa?

When you regularly and proactively care for your spa, it will keep giving back in valuable, healthy ways. Hot Spring spas are designed to make it easy for you to monitor water quality, clean the filters, and protect your spa from the elements. Follow these tips to keep your home spa in tip-top shape and to minimize the time and cost of repairs.

How to troubleshoot an issue with your spa?

To troubleshoot an issue with your spa, locate your specific problem in the chart below to help determine a probable cause, and then apply the right solution. Do you need to call a professional technician? Do you need to call a professional technician? Adjust the total alkalinity and pH.

Why is my Arctic Spa hot tub overheating?

So the first thing to remember is that the Arctic Spa is designed to utilize the excess heat from the motors to heat the water. So as we go through that filtration cycle, that motor is going to be running and it’s gonna be generating heat.

What to do if your Sundance spa heater is not turning on?

Heater is deactivated and pump may not turn on. Flow/pressure switch is defective. These steps should only be taken after checking and testing the above steps. With the circ pump and the main pump off, test switch operation with an ohmmeter in the continuity position, test for continuity across switch terminals.

Why does my Sundance spa go into Oh error code?

Another issue that comes up and is an indication of a bad temp sensor is the temperature reading becomes inaccurate or the spa is going into the OH error code. If you power the spa down and power it back up it may work for a while but will do the same thing again. You need to replace the Temp Sensor. 3. FLO or OH Error Code

What kind of circulation pump does Sundance Spa use?

Note: This test only works on 850 Series with Circulation Pump prior to 2001: Try turning the #1 pump which is 2 speed.

How can I tell if my Sundance spa filter is defective?

The only way to test this is to make sure there is no loose debris in the spa, then pull the filter out and see if the flow error goes away, if it does, it is the filter. 2. Defective Circ Pump or Flow Switch: Need to check for Circ Pump operation.

What to do if your hot tub breaker tripping?

First: Turn the Breaker off and test with a meter to be sure you have no power coming to the spa. Second: On most Flo Thru Heaters, you will find 2) Heater Terminals, with a 3/8″ Nut holding a copper strap or wire attached to the terminal from the Circuit Board.

How do you reset the high limit on a spa?

Or it might need a reset from time to time for no known or serious reason. Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell. If the water temperature in the thermowell is the same as the water temperature in the rest of the spa, the switch is damaged and needs to be replaced.

How does the high limit switch on a hot tub work?

Your high limit switch measures the water temperature by either a capillary tube attached to a bulb or a mounted sensor. If the switch detects unsafe temperatures, it opens to break the circuit and keep the heater from literally melting down. Once the water temperature in the hot tub has decreased, the high limit switch must be reset manually.

What does the Hi limit on a spa mean?

Hi-Limit: A safety backup if the Thermostat fails. The Hi-Limit shuts off the heater or spa equipment when it detects a water temperature of 109° – 116°. The Hi-Limit on most newer spas can be reset by turning off the spa’s main power supply, and allowing the water to cool to below 100°.

What’s the reset button on an old spa?

Older spas used mechanical Temperature and Hi-Limit switches. This type of Hi-Limit can usually be reset by pushing in its reset button, a red or black button located on the heater or equipment pack (see your spa manufacturer’s instruction manual for exact location on your spa).